2. misc-audio
  3. 169256-101338

Audiophile Fuses - Are We Certain They Provide Protection?

This thread isn't posted to debate whether sonic benefits can be recognized from audiophile/after-market fuses.  That topic has been well debated through numerous threads already.  What I'm curious about is whether today's audiophile fuses are certain to provide protection to your gear - afterall, that is the absolute main function of a fuse in a circuit design.

I was struck recently reading a thread dating back to 2014 on the Audiocircle forum where the late Roger Modjeski was absolutely beside himself and angered by professional reviewers and manufacturers alike for leading consumers astray (in his opinion) towards use of these fuses, from a first-hand account of damage inflicted on one of his amps.  

Re-posting his message below:

I had several email exchanges with the maker of Tuning Fuses and got the same Red Herring responses. My first experience with his product was in an RM-9 MKII that came to me for service with eight tuning fuses (one for each tube) in place of my specified HIGH BREAKING ceramic fuses. The tuning fuse's inability to do their job properly had blown the wirewound cathode resistor, which I had never seen before. I study every failure and this one caught my attention because it takes a lot of energy to blow that resistor. Its wire is much stouter and of a very high melting material, any fuse should go first.

Of course I opened up the fuse and looked at its construction. It was made in such a way as to be the worst possible fuse for that application. I called the distributor here and asked is it was a high breaking fuse and suitable for a tube fuse. He didn't know what that was. I said well the fuse specified for my amp is high breaking and ceramic. He said that because his fuse was ceramic also it must be OK. This is very naive. He doesn't know and perhaps the maker doesn't know that a high breaking fuse is made a different way, though from the outside it looks the same.

These fuses are totally inappropriate for any high voltage DC application such as a tube fuse in an amplifier. What also amazed me is that these fuses cost more than most tubes. I felt sorry for the owner who had been led down this path by irresponsible magazines like Positive Feedback. Not only did this fuse not protect his tube but it did not protect his amplifier.

The maker of these fuses, like many makers of tweaks will certainly get no admiration from me. What gets me is why so many people want to play with tweaks rather than make real improvements in their system like bi-amping, adding a good subwoofer and simplifying the signal path.

As this experience is now 7 years old I wanted to survey our forum to see whether high-end audio fuse manufacturers are providing data that would give the audiophile community assurances that use of their fuses first and foremost provide adequate protection.  I welcome any input.
128x128three_easy_payments
goose
694 posts
 

@millercarbon I had a blue and it blew.  Was sent an orange at a higher value and it blew in the 360 pre amp.  I don't know what fuses SR are using but this is what it looked like when I peeled back the organge covering on my system page.  I'm not trying to bash SR since I have their HFT'w which I like.  

 

oregonpapa's avatar
oregonpapa
4,867 posts
 

I have all ARC electronics. I’ve gone through the whole gambit of SR fuses. The Reds, the Blacks, the Blues, the Oranges, and now the Purples. I had one Black fuse blow in my ARC Ref-75se upon turn on. That’s it ... one fuse out of all of those listed. All of them were at ARC’s recommended values too. Conclusion? ... Buy ARC. :-)

Frank

 

 

rlb61
789 posts
 

If one is going to start messing around with boutique fuses (which I don’t recommend), then don’t forget to adjust the flux capacitor resistor output so that the conditioned power intake is aligned properly with the faraday cage.😉

rsf507
2,321 posts
 

If SR will not put in writing their fuses are UL certified or EU certified why would anyonewant to take a chance with them? For a representative to just say they are and trust them at their word is just plain ignorant IMO. 

mitch2
3,995 posts
 

Some years ago, I discussed boutique fuses with a service tech at Ayre Acoustics.  He told me they had internally discussed their support of boutique fuses (such as HiFi Tuning) and whether they would warranty units that failed with a boutique fuse installed.  At that time, it sounded as if they were on the fence internally about supporting the use of boutique fuses, but they would be reluctant to publically denounce boutique fuses unless they started to observe direct evidence of those fuses causing failures.

I have yet to hear about equipment failures being attributed to using boutique fuses, even from users who "size up" to the next higher fuse, as sometimes discussed in these forums.  Given all of the SR, Audio Magic, HiFi Tuning, Acme, etc. fuses being purchased by audiophiles, I doubt "assurances" are even necessary.

More to discover