ZD, Mesch, Mapman, 77Jovian, thanks very much for the nice words. And kudos to Frogman if my suspicion is correct about there being a subtle cleverness underlying his post.
French_fries, I doubt that you’ll find a more thorough take on the 500-C receiver than in this review. Be sure to read the entire review, though, including the measurements section, to get a well balanced perspective.
Also, keep in mind that the 500-C contains something like 18 or 20 tubes, and a correspondingly large amount of circuitry, which increases the likelihood that whatever example of this receiver you may acquire may have condition-related issues, depending of course on the thoroughness of whatever restoration efforts it may have previously undergone.
Speaking more generally, I don't have experience with receivers of that era, but I do have a fair amount of experience in recent decades with 1950's and 1960's separates produced by the leading manufacturers of the time, and in a couple of cases also with integrated amps. Based on that experience I'll second Mapman's comments, but I’ll add the proviso that vintage vs. modern comparisons need to be based on present day selling prices that are at least somewhat comparable.
For example, I would expect that the modern day $2K tube component you referred to would not include a tuner, and would perhaps also not include either a preamplifier section or a power amplifier section. So that comparison adjusted for comparable functionality would involve modern components costing well upwards of $2K, while I suspect that a 500-C in reasonably nice condition, or alternatively a comparable vintage integrated amp, could be found for considerably less than $1K, especially with some patience. And so if the modern component(s) in that comparison were to come out ahead (and assuming that the vintage component is in top condition), it would probably say more about the price differential than about "vintage vs. modern" per se.
In general (there are always exceptions, of course), IMO a **well restored** vintage tube component ca. 1955-1965, from one of the better manufacturers of the time (including Fisher), will handily outperform most of the solid state components that were produced during the subsequent 15 years or so. And assuming appropriate system matching will generally provide very pleasing performance compared to most modern components selling at or somewhat above the same price.
Best regards,
-- Al
French_fries, I doubt that you’ll find a more thorough take on the 500-C receiver than in this review. Be sure to read the entire review, though, including the measurements section, to get a well balanced perspective.
Also, keep in mind that the 500-C contains something like 18 or 20 tubes, and a correspondingly large amount of circuitry, which increases the likelihood that whatever example of this receiver you may acquire may have condition-related issues, depending of course on the thoroughness of whatever restoration efforts it may have previously undergone.
Speaking more generally, I don't have experience with receivers of that era, but I do have a fair amount of experience in recent decades with 1950's and 1960's separates produced by the leading manufacturers of the time, and in a couple of cases also with integrated amps. Based on that experience I'll second Mapman's comments, but I’ll add the proviso that vintage vs. modern comparisons need to be based on present day selling prices that are at least somewhat comparable.
For example, I would expect that the modern day $2K tube component you referred to would not include a tuner, and would perhaps also not include either a preamplifier section or a power amplifier section. So that comparison adjusted for comparable functionality would involve modern components costing well upwards of $2K, while I suspect that a 500-C in reasonably nice condition, or alternatively a comparable vintage integrated amp, could be found for considerably less than $1K, especially with some patience. And so if the modern component(s) in that comparison were to come out ahead (and assuming that the vintage component is in top condition), it would probably say more about the price differential than about "vintage vs. modern" per se.
In general (there are always exceptions, of course), IMO a **well restored** vintage tube component ca. 1955-1965, from one of the better manufacturers of the time (including Fisher), will handily outperform most of the solid state components that were produced during the subsequent 15 years or so. And assuming appropriate system matching will generally provide very pleasing performance compared to most modern components selling at or somewhat above the same price.
Best regards,
-- Al