What are you sending Porn? I can find all that I need somewhere else.. LOL.
Which wire is it?
How you doing oldtimer, I mean oldhvymec. That's just the problem; I can't do a schematic; I cannot even send a photo because there is no place to upload a photo. And why I can't do a schematic? Because I don't know what goes connected to what. We have a wire just "swinging in the breeze" that is loose, one end from the positive of the LED and the other end ?? Don't know where it goes! I can see the high voltage wires B+ going into a 5-lug connector and soldered to lug #1. Lug #2 is empty. At lug #1- it has also connected to it, 2 resistors in parallel bands RED-VIOLET-YELLOW 5W each which connect at the other end to lug #5. Lug #2 is EMPTY. Lug #3 is GRD. Lug#4 is EMPTY. At lug #3 is the resistor in question: 100K 5W ..... and the other end is BLOWN UP. So what do I have? I have one leg of a resistor blown up and I have one side of the + wire of the LED in the air.
IF I HAD A SCHEMATIC or a pictorial I could easily see where they are to be connected. Right now I can only guess. I am counting on your vast experience to show me. Was that you that sent a link from the UK? Let me take a peak at it and see if I can solve it.
Hope to hear from you shortly. I like your commentaries.
Hey Oldhvymec.. I can see the pictorial, finally!
BTW: Those pictorials also show the bias potentiometer OUTSIDE of the chassic. My amp is so old that the bias is inside. I think that is a fabulous idea to be able to modify my old amp. The pictorial is not that clear. Maybe we can blow it up some to see it clearer.
@russ69 I think I’d be all over Cary. HEY! Provide some service or provide the info I need to fix it myself. I’d get someone on the phone to tell me I’m SOL, then I would tell them, bad mistake, you guys are going to be my hobby, and it’s going to get ugly, your call.
They don’t troubleshoot over the phone any more. Been there done that with them and seemingly got the last lead designer-tech in trouble there helping me with my V12R mods. He quit two weeks later. Felt bad. He went on to new things, now designs and builds pro audio tube microphones. If lucky, will just tell you to send it in and charge for the repair. Double-bubble and double-box if you do.
Probably better off sending it to a good local tech, and many can do as good or better job. Avoids shipping cost or risk of transport damage. Have them replace the coupling caps and a few resistors with better ones while it’s there. That amp can sound a lot better with a few upgrades. Some techs like to throw in a Triode/Ultralinear switch too.
Thanks for all your input and ideas. I'm sure they are all valuable. I have a few issues that may clarify some of my uncertainties. 1- I am 75 years "young" and cannot LIFT a 50 lb amplifier by myself; much less flip it over.
2- Although I am a retired engineer, I have some difficulty following a pictorial or schematic when there are no values attached to them. It does not help me to see a schematic drawing of the item in question if I do not have a voltage reading or description of the item in question.
3- Not having readings I cannot tell if the LED is burned out or damaged or shorted out or the voltage readings on either side of the resistors are good or not [regardless of resistor reading which seem OK].
4- Last but not least, I am retired living in Panama, Republic of Panama where the Panama Canal is and there are very few (I have not found one) "local TECH" that are EVEN WILLING to look at a wired amplifier. I am doubting that anyone under 40 years of age has EVER seen a point-to-point wiring.
As an example I asked: What size or voltage reading do I need to get the LED? Answer: Oh, don't worry about that. They're all the same. "Say What"?
So, what am I asking for? HELP. Help from someone knowledged enough to try to give me some decent advise.
My last question is: Is there a difference in the LED used? How do I check if it is shorted out? The power fuse is blowing up so something is not going right.
If you have not already done so, maybe you could ask the folks at Sound "N" Music or GER Global Electronics Repairs there in Panama if they know of someone who can come to your place, like an old TV repair person use to do in the old days :) Might be worth a try.
Sound 'N' Music Electronics store in Panama City, Panama
Address: Av Central, Plaza Cinco de Mayo, Panama Phone: +507 212-1801
Hello decooney. Great info. Sorry to say that Sound & Music are a retailer of home sound equipment and have decent technicians that know how to INSTALL these equipments. They do very little repair.
They're recommending someone else, but the truth of the matter is that it is most difficult to find someone who knows about point-to-point wiring. Everyone knows about chips and circuit boards and mother boards. I will keep on trying.
I was just thinking that Sound N Music may know of someone in your region maybe within a 4hr circumference. Some of these hidden techs work out of a basement of their homes, and shops contract and send out to them. It's not always openly shared or advertised.
In any case, someone who understands basic wiring and point-to-point circuits will be most helpful. I'm friends with an ex-Cary Tech who sometimes does work, rarely, and that would require costly shipping too. Worth it to keep looking around you for that less-known tech in your area. They do exist some times, adult easter egg hunt. Good Luck.
Sr oldhvymec. With all due respect to someone that appears to know what the problem is and knows how to fix it ...... It does no good to give me a "hint". This is not a school atmosphere. I have a problem and I am going to the "forum" and am asking for help. I cannot solve this problem either thru Cary Audio or by getting into the amplifier to track the problem if I do not know values. I know what a resistor is, what a cap is, lugs, etc. but if I do not have a value attached to the resistor or cap in the schematic and have no voltage values, I am stuck. So please, if you know the answer, don't give me a hint or tell me to open a 6-pak, HELP ME FIND THE SOLUTION. If you want to charge me for your knowledge, let me know, but don't give me hints. I am not a kid!
Does anyone have any idea the type and voltage/amperage requirements are for the power LED in the Cary SL-70B amp? I have changed the resistors in question, and when I plug in the amp, the power fuse 3 AMP SLOW BLOW ---> BLOWS UP. I'm thinking the power LED may be shorted perhaps? But where do I get a new one? What is the model number? When I walk into a tech shop and ask for a Power LED what other info is needed to obtain the correct one?
Hello all. I realize this thread is about the amp, but I have a problem with my Cary CD 306/200 and have run out of options. Does anybody have a schematic diagram for this player ? It’s been at the shop for months and they are not able to troubleshoot it and Cary calls it obsolete with no support. Any help or lead would be greatly appreciated.