Discuss The Viv Lab Rigid Arm

I am trying to do my due diligence about this arm. I am just having a hard time getting my head around this idea of zero overhang and no offset. Does this arm really work the way it is reported to do?



How do you know you actually have the alignment you say you do?  Here is a test report of three random samples of stylus assemblies from an order I placed.  This is representative of the best numbers I have seen thus far and are kind of terrifying.

I don't care how great of a protractor you have if you are aligning to a cantilever without consideration of possible diamond set error then I see the baby going out with the bathwater.  JR addresses this by optically placing a number on the Zenith error and then providing a protractor with the ability to correct for this error.  Next we can open the can of static vs. dynamic worms and observe how much skating forces and groove modulation come into play here as well.  In many setups, when you adjust azimuth to better crosstalk numbers you also change your alignment.  Add or remove a gram of anti-skate correction and you have just changed your alignment.  Its really easy to brag about a preferred alignment and the precision of your setup and quite humbling to realize you are actually nowhere near where you thought you were.



Mijostyn, It does not behoove you to use the term "scientific" in this context to justify any of your thinking on the subject. Your approach fails the scientific method on first principles. You are operating within a belief system that starts out with TAE = bad. But I concede that neither of us has the actual data, apart from Intact Audio’s data, to justify any claims at all. I can say that when Dave "fixed" the zenith error on my ART7, it suddenly sounded better. He also measured the resulting TAE which reverted to the textbook look for a well aligned cartridge in an overhung tonearm. This certainly is consistent with the notion that TAE matters when zenith and the alignment according to accepted algorithms are both correct, for an overhung tonearm (with AS applied and azimuth set to 90 degrees, as well). Can you find a paper in the audio literature where the effects of TAE on the audio signal were looked at with a ’scope or some other valid method, that quantifies distortion of one kind or another? I cannot so far. This subject is only interesting if you approach it with an open mind. And I certainly don’t blame you if you don’t want to buy an underhung tonearm, but it does hamper your capacity to make a judgement on them as a class. Like I said, I took a flyer because the Viv has received near uniform positive reviews, because I could buy at a considerable discount in Japan, because I have also had good results with the weird RS Labs RS-A1, and because a major company (Yamaha) has seen fit to produce an expensive turntable with a built-in underhung tonearm. (I don’t use the RS-A1, because it is very finicky and most of all because it dangles the counterweight from the rear of the arm in order to place its center of gravity at the surface of the LP. This leaves the CW to sway like a pendulum, literally on off-center LPs, which cannot be good for the cartridge suspension. But the RS-A1 displays many of the positive good qualities of the Viv.)

I did find some papers on this subject.  Here is a long post from Vinyl Asylum.  The author makes the good point that TAE affects only frequencies encoded in the horizontal plane (low frequencies), and he states that the distortion due to TAE is Harmonic in type. That may explain why if there is distortion due to TAE with the Viv and similar underhung tonearms, I (at least) do not find it objectionable.  Also, the level of distortion is inversely proportional to velocity, meaning HD will be higher near to the inner grooves. The math is complex and will take some time for me to digest:


Finally, the post opens the door to think maybe the skating force is more obnoxious than TAE.


Dear @intactaudio : You don’t get it my point or I can’t explain it in the rigth wat but your charts goes exactly on what I listening during those yesterday tests: the overhang change/error produce a kind of distortion that’s detected when the alone " error " in the offset angle not only is lower but just can’t detect it in easy way. This is my issue.


In the other side, in this thread I posted that the angular error is only a part of the whole subject because a tonearm is a lot more than tha and I posted about that well damped VIV pivot bearing and its arm wand O rings and the like.

Change in overhang alone is truly sensible and audible, we can see that a tiny difference around only 0.4mm between Löfgren A and Löfgren B alignments that tracking distortion goes lower in the B alignment and both A and B alignments have the same offset angle.


Yes, even if we have the best tools to make the cartridge/tonearm set up the perfect set updoes not exist because LP groove after groove surface is not totally flat but full of waves and micro-waves where the stylus tip it’s looking different VTA almost at each groove. I posted several times about as I posted that changes in VTF/VTA/AZ and the like change the original set up, it’s the reality of the imperfection of analog as is the fact that even top cartridges comes with no perfectly centered stylus tip at the cantilever even sometimes comes with not centered cantilever.

Btw, here I don’t mentioned that lewm does not listen the high distortions developed by the VIV ( because " not golden ears " ) or that his system has not the resolution to do it but I posted the other way around and don’t diminish him or his system in anyway. I have respect for lewm, I know who he is.

Every one of us know about those " nice distortions " but no one but the VIV owners experienced a totally NEW kind of " nice distortions " ( lewm I posted that it’s need it to look at what sort of distortion as you said but with my words ) and almost all know that our ears are not the best " tool " to detect not only that kind of distortion but several others because during LP playback what we are listening and that we like it’s totally full of distortions.


No one here is discovering the " black thread ".

Still my question abou the stylus shape is On and with out answer from you .




@lewm : " Until then, your complete conviction that you alone are possessed of the "truth" rings hollow to me. Is your close-minded attitude any better than the behavior of the AHEE that you so revile? "

You are who think that because here for what I posted tells you that I’m not a close-mind but the other way around. What you could think is only that what you think but not what is my attitude on the whole subject .

I don’t remember that in this thread you mentioned or accepted that are listening added unique kind of distortions by that high tonearm offset angle and : Are you saying I’m close-mind? .


Btw, I was writing my post when you already posted that link that I don't read yet.



Simple, I have a very powerful USB microscope and a computer program that allows me to snap lines and it automatically determines angles. I detail each and every cartridge I buy. If there is an error I correct for it, but frankly all my cartridges are in the 9 to 13 thousand dollar range and are beautifully made. If I ever got a cartridge that was that bad I would send it right back.