Help. System sounds thin and bright or harsh

Hope this isn't redundant tried to post in Tech Talk

Just moved my system to a new home/sound room and it still sounds harsh and a bit thin despite supposedly "warm" sounding Harbeth 30.1 speakers. This issue is not new and I had put the blame on the old listening room.  Can't figure out what the problem is. I listen loud at 80dcbl or higher and sit nearfield about 8 feet from the speaker plane. (sound is thin and bright from afar as well) I have experimented in both homes with speaker placement, toe-in and the like. Speakers are placed a lil over 3 feet from the rear wall and about two and a half feet from side walls.  I feel something is off. Perhaps a component or two that is known to be tipped up in the highs and a lil bass shy?? Also, I leave all solid state components fully powered up 24/7. (not the tubes)


Modwright/Oppo BDP 105 disc player  (all mods with tubed power supply and pricey NOS tube upgrades throughout)  Looking to replace once the harshness/bright issue is nailed down.

Parasound JC2 Preamp

Pass Labs X250.5 Amp

Harbeth 30.1 stand mount speakers

Puritan Labs PSM 156 power conditioner. (less "edgy" sound with it in system)

System is run all balanced with fairly costly Cardas interconnects.

All input is welcome. Thanks in advance.

Happy listening.




I’m also using Puritan PSM156 and I like the sound of my Pass Labs amp being plugged directly into the wall outlet as well. Could be system compatibility when it comes to how all the component interact with each other (input/output impedance, gain, input sensitivity). 

@cymivka - I have x250.8 and psm156. They work beautifully. If you're looking for preamp, I recommend LTA MicroZOTL preamp. I just got it and sounds wonderful with Pass and Falcon Ls3a/5, which tells me it would also work well with harbeth. 

If you are using any rigid footers like cones, spikes, Rollerblocks, try removing them and replace with something pliant. If your issue is resonance related this should tell you. 

A fix no one has mentioned yet.

I've had the same problem over the last few years. Most of my listening time is at night from 11PM to 2AM. Supposed to be the best time to listen. System would start off great and get progressively brighter and thinner. Tried everything, amps, speakers, room placement, vinyl, digital, room acoustics. Nothing really helped. 

I started having a problem with the Oppo 105. Sometimes it would get stuck playing off the external hard drive. Had to be unplugged to unfreeze the gui. My VTL ST150 popped a resistor causing a tube to glow red. 

I joined the free Orchard Audio Starkrimson amp tour on the Hoffman website. The sound was so nice I had Leo build me an amp. New amp arrived and it wouldn't play! It automatically went into protection mode. The voltage was too high. As an experiment ran the amp with 300ft of 16ga extension cords. Wanted to drop the voltage. The amp played!

I now have the amp and Oppo plugged into a 20 amp variac set to 110 volts. Sounds nice throughout the night and, fingers crossed, the Oppo hasn't messed up since. Check your voltage. Mine steadily increases later at night. Funny thing, my big wire dedicated ac lines actually made the problem worse. Normal house circuits had more voltage drop and sounded better.

Loving the system and new amp.

Good luck,



thanks for your input.  I still come back to the oppo as my main problem aside from room maybe too big for the Harbeth 30.1's (no rear wall) I find i cannot tolerate music past 70 dcbls. voices "kill" in trying to get the music to excite the listening room. Very irritating.  I am running the oppo as a transport through a puritain 156 conditioner into a very good dac. Using an after market power cord (Puritain).

Sounds pretty good with the right recording at moderate levels.  Looking to try out another cd/transport before replacing the oppo.  

Also need to check voltage levels when sound gets worse.