I agree, regarding the X-former location. Ideally; the entire power supply would be in a separate chassis, but- we ARE talking about a sub-K unit here. I know that discrete use of TI's EMI/RFI shielding can make a marked difference, within the unit. PS Audio makes this statement about their gain stages: "The GCPH is built around two discrete and fully class A balanced gain stages: a high gain, low noise input stage and a Gain Cell for the output stage, with the passive RIAA curve between the two stages." They DO say that the unit is a, "true balanced design from input to output", but don't claim it to be Class A, all the way: (http://www.psaudio.com/products/audio/perfectwave-accessories/gcph-phono/). I believe PS recently moved all their manufacturing back to this side of the pond. I'm certain yours was not the only problem unit produced over there. As far as marketing to them: Given the technical ignorance of the average, "audiophile".....Well, have you ever read the crap/hype printed in an 'Audio Advisor' brochure? Happy listening!
Impressions of PS Audio GCPH
I recently obtained a PS Audio GCPH and there are a few observations of the circuitry that surprised me, in the face of the advertised information provided by PS Audio.
First, as some have mentioned in the past, the noise performance limits the actual gain you can use with this device. For example, the 48 dB gain setting is only 48 dB when the front panel gain control is maxed out (full CCW). But if you use full CCW, the noise is intolerable. In my system (Parasound JC2 line/JC1x2 power/B&W 830d) I can use a max gain of 12-1:30 on the GCPH before I can hear audible noise. That is with the input source impedance loading set to 1K (which is typical for midband MM cart impedances). Setting the loading down to 100 Ohms improves noise a bit. The noise was not all hum, but mostly white thermal noise, which means the transformer orientation inside the GCPH is OK. At the volume control setting of 1:30 (12 being straight up), I measure the gain at 40 dB with 3 mV (at 1000 Hz) in, 300 mV out. Considerably under the 48 dB stated.
Checking the other gain settings I also found that the usable gain is about 6-8 dB below the marked settings. I checked the highest gain setting of 66 dB and got about 60dB actual usable gain (.5 mV input, 500 mV out) at the 1:30 volume postition).
I think this is still high enough for most cartridges, except for really low output (150 micro-volt) MCs. Its just that the advertised and marked settings are misleading, particularly if you need the higher gains.
A word about my noise tolerance criteria. I find noise level unacceptable if I can hear anything out of the drivers (with my ear at 6") at my normal listening volume. With my CD playback system (CA 840/Bryston BDA-1) the noise level is undetectable at this same level (and to even much higher gains), so the phono preamp should be able to reproduce this as well.
The other observation I found concerning was that the actual circuitry uses two monolythic IC circuits for the preamp. The device is an Analog Devices SSM2019B pre-amp. I was under the impression that the GCPH used only "fully balanced True Class A circuits through-out" (Ryan Conway, PS audio review on Audio Advisor), meaning discrete Class A circuitry. It is not. The SSM2019B is not differential balanced, and its questionable whether it is Class A biased either. The gain cell modules appear to be output buffers.
First, as some have mentioned in the past, the noise performance limits the actual gain you can use with this device. For example, the 48 dB gain setting is only 48 dB when the front panel gain control is maxed out (full CCW). But if you use full CCW, the noise is intolerable. In my system (Parasound JC2 line/JC1x2 power/B&W 830d) I can use a max gain of 12-1:30 on the GCPH before I can hear audible noise. That is with the input source impedance loading set to 1K (which is typical for midband MM cart impedances). Setting the loading down to 100 Ohms improves noise a bit. The noise was not all hum, but mostly white thermal noise, which means the transformer orientation inside the GCPH is OK. At the volume control setting of 1:30 (12 being straight up), I measure the gain at 40 dB with 3 mV (at 1000 Hz) in, 300 mV out. Considerably under the 48 dB stated.
Checking the other gain settings I also found that the usable gain is about 6-8 dB below the marked settings. I checked the highest gain setting of 66 dB and got about 60dB actual usable gain (.5 mV input, 500 mV out) at the 1:30 volume postition).
I think this is still high enough for most cartridges, except for really low output (150 micro-volt) MCs. Its just that the advertised and marked settings are misleading, particularly if you need the higher gains.
A word about my noise tolerance criteria. I find noise level unacceptable if I can hear anything out of the drivers (with my ear at 6") at my normal listening volume. With my CD playback system (CA 840/Bryston BDA-1) the noise level is undetectable at this same level (and to even much higher gains), so the phono preamp should be able to reproduce this as well.
The other observation I found concerning was that the actual circuitry uses two monolythic IC circuits for the preamp. The device is an Analog Devices SSM2019B pre-amp. I was under the impression that the GCPH used only "fully balanced True Class A circuits through-out" (Ryan Conway, PS audio review on Audio Advisor), meaning discrete Class A circuitry. It is not. The SSM2019B is not differential balanced, and its questionable whether it is Class A biased either. The gain cell modules appear to be output buffers.
- ...
- 40 posts total
- 40 posts total