Linn's advice about bi-amping; question


I have a Linn set-up including a Majik integrated amp, an LK85 power amp, a pair of Tukans and a pair of K400 bi-wired cables. I asked Linn about how best to bi-amp, and here was their reply:

To bi-amp Tukans remove the shorting link from the Treble/Bass terminals of the speakers. Remove the jumper from the pre out/power in jacks of the Majik. Hook interconnect cables from the pre out/power in jacks of the Majik to the LK85 input/outputs respectively. Then hook the speakers up to the amps with separate speaker wires.

It's the last part I'm not sure of. Does it mean that I will need a total of 4 pieces of K400 wire (i.e. 2 pairs), or am I saved by the fact that K400 is already bi-wired. Your advice appreciated.

Thanks.
kdl6769
From what you've said above, it sounds as thought you've got the K400's in a bi-wire configuration (ie. Two connectors on one end, and Four on the other) All you'll need to do is modify, or have it done for you, the one end of each speaker wire, so 4 connectors will exist and both ends, or all the wires are singley terminated.

Since you've had to pull the pre out to power amp in jumpers, I don't know that the Majik could still be used as an amp.....call Linn for that one (888)-671-LINN.

If it does, then just hook one set of speaker wires from both the left channels of the Lk85 and the Majik, and the other to the other channels. (keep the amps matched), then connect the wires to the speakers, after removing those little plates on the back of your speakers, you'll need the little wrench that comes with your speakers, or improvise as you'll have to pull off the gold covers on each terminal on the back of the speaker. Don't do all of them at once as many Linn crossovers are held in by these and then you've got to pull out drivers..... and match all the wires from amps to speakers!

As an aside, Linn recomends using the best amp for the tweeters, for all speakers.....I know, sounds funny, but that's what they'll always say.

Can you go Activ with that bi-amp combo??

Ken
I am not certain that I understand what you said.

I am not familiar with your equipment.

However, There are two distinct things you can do. 1)bi-wire and 2)bi-amp. These are completely different. Bi-amping is FAR more beneficial. In order to Bi-amp you need to disconnect the passive crossover IN your speakers which I do not see in the instructions so you are actually bi-wiring here apparently. Just so you know the diff. Hope I am not confused by your instructions.

Sincerely, I remain
The instructions looked like bi-amping instructions to me (e.g. removal of jumpers).
Kind of confusing, but here it is...

BE SURE THE SPEAKER JUMPERS ARE REMOVED and all power is off. You can short your amps if not

-Remove speaker jumpers
-Each wire on the K400 should have a connector (4 left/4 right)Your left set of K400 wires will transport the treble down one half(pair +/-) and the bass down the other half(pair+/-) to your left Tukan. The right set of k400 will carry the treble/bass to signal to the right Tukan
-Remove the pre-amp jumper on the Majik
-Install L/R rca interconnect from "pre out" to "input" L/R on the LK85
-Connect the L/R speaker treble +/- to the LK85 (top connection on the rear of your Tuks
-Connect a L/R pair of RCA interconnects from the "out" on the rear of the LK85. Run this "back" to the rear of the Majik and connect at the "amp input" (the remaining side where the pre-amp jumper was removed)
-Connect your bass speaker wire L/R for each Tukan from the Majik to the lower L/R inputs on each Tukan

Your low level L/R now comes out of the Majik into the LK85 to power your tweeters L/R, it daisy chains back low level L/R from the outputs on the LK85 back to the Majik amp section to power you woofers L/R.

You now have a separate amp powering the L tweeter, a separate amp for your R tweeter, a separate amp for the L woofer and a separate amp for the R woofer, each being supplied by it's own set of speaker wires +/-.

You are now "bi-amped" correctly.

Hope this helps
Dan
dedicated audio