NHT T-6 speaker placement


I am getting ready to do some wiring and wonder which would be best for rear speaker placement. I have two NHT T-6 wall/ceiling mount speakers. Should I mount them to the walls or ceiling?

My room...I hope this makes sense. The wall behind the listening area in my basement is the one with the staircase on it. Under the stairs (looking at that back wall it would be on your right) is a wet-bar / counter area with washer&dryer built in cabinets under the counter. The counter comes out about the same plane as the half wall going up the stairs making a recess in that portion of the wall. A door to a storage area is next to the counter area on the right. On the left, about 2/3 of the distance from the approx. 19x30 ft room is the staircase landing.

If I mount them to the ceiling, I can put them equal distance (just a few feet) behind the listening area and ahead of both recessed areas. If I go for the wall mounting, the left rear speaker would be in the recess area next to the bar sink and the right rear speaker would have to be in the stair well just a foot or two into the landing.

Thanks for your thoughts.
stearnsn
because of constraints with the structure itself, I ended up with placement just behind the listening couch on the sidewalls. It seems to work pretty well.
Post removed 
Post removed 
Basically, in speaker placement, everything is a BALANCE! There are trade-offs, compromises, and factors to consider, and it all needs to balance out for best performance. Or rather, it "should", if performance matters.
When it comes to rear speaker placement, as with mains and sub, I think it's wise to consider many factors. However, the main consideration for any speaker setup (in relation to the seating possitions) should be the fundamental "frequency response" from the speaker! This single issue alone, I find, is the single most neglected factor for most all, even from professional installers!!! It's sad but true. What happens, when response isn't considered, and poor speaker/seating locations are implemented, is frequency distortion, dynamic range restrictions, tonality shifts, "holes in the sound" between sub and speakers, balance issues in thesound,"boomy/peaky" unatural overall sound, obscuring of detail and vocals, imaging issues, etc, etc! High fidelity gets down to not only good fundamental equipment, but a balance of sound, tonaility, soundstaging, imaging, perspective, and dynamic range, including good acoustics and treatments, and it should all be considered if you care about sound.
So, for me, speaker placement must be first and for most be about oveverall SOUND QUALITY!!! Again, this is the most neglected factor usually.
Then considering proper stearing, envelopmenet, lack of distraction from the speaker (pulling you from the movie) from a "dominating speaker" blasting in your ear, soundstage cohession from seatting possition(s), etc.
As for placing speakers for proper stearing, soundstaging, and envelopment, there are going to be some preferences for each, but also some recommendations fundamentals.
For side speakers, you should try to go high for monopoles, and even a bit behind the main seating area. For dipoles, you should go dirrectly to the sides of the seating area, and you can go lower down the wall. For rear/back speakers, the same applies mostly, but I tend towards the middle/back of the wall for monopoles, or between seating possitions in an "even number seating arrangment", and dipoles dirrectly behind the heads, when using those! This also tends to yeild the the flattest response potential in the right seating arrangement, but it depends. (I consider all of this with mutiple seating arragnements, as opposed to "single seat" set-ups. Again, I consider the flat response when doing this, for solid fundamental performance and accurate sound fundamentals.
So, in short, things must be measured, balanced, weighed out, tested, tried, tweaked, even EQ'ed, and properly integrated with respect to all the other variables, seating and speaker possitions, crossover points, etc, etc.
This is why your average DIY'er has a very difficult time in achieving hi-fidelity, even superb, world class results from their investment!!! It takes years to learn what's all going on in a system.
I hope my suggestions help. Also, consider some of the newere processors with excellent "room correction" applications, and EQ circuits. These help greatly, especially once the fundamentals are adressed.
Good luck