PC Recommendation for Furman Conditioner

Hello. I have a Furman SPR-20i voltage regulator/conditioner and require a 20A IEC connector for my power cord.

I'm wondering if anyone can provide any recommendations on a PC to use. I have a VH Flavour 4 I'm currently using and could replace the 15A IEC with a 20A IEC as well instead of getting a new complete cord, (any recommendations on a good 20A IEC).

Also, I've been using a fair bit of stealth cables in my system and like how they present detail and neutrality in a laid back manner so I have been considering a Stealth PC, (never had one).

Also considering in no order....

Tel-Wire (don't think they have a 20A IEC option though)

With the Lessloss I've heard some people don't think it's a good cable for a power conditioner, (although others say it is). I like the fact that it has high quality connectors though. With the Kaplan, it looks like the 20A IEC is only a 10 dollar part and while that may not make it bad, some feel the connectors are the most important part, (more so than the cable), but some feel it's close to a Kubala Sosna Emotion in terms of sound quality, (the only important measure).

Anyway, as you can see, lots of options and I know the "you'll never know, cables are so system dependent, etc" feeling. I'm just looking for opinions/thoughts. Thanks in advance.
Kimber makes the PK-10 Gold with the 20amp IEC option and retails for about $350. It isn't shielded for better sound so you need to keep it away from ICs and speaker cables but shouldn't be a factor in using it from the wall to the conditioner.

Of course you have your selection of Shunyata PCs but I haven't heard them. I have one of the Kimbers between the wall and my Hydra and like it for my main amp that draws a lot of power.

You could give Mr. Cline at TelWire a call and see if he could provide an appropriate IEC to meet your needs.

As to why I offer the Hubbell brass contact h320c 20amp IEC on the KaplanCable as an option, its because it works very well with the copper plug I use. Heck, Synergistic uses Leviton plugs on cords that are amazingly good, and Kubala Sonsa uses Pass & Seymour. Why? I don't know, as they don't gel well with my wire and topology.
I've a satisfied customer using 2 20 Amp IEC cords for his BPT balancing conditioners, and another using his on the same Furman as yours. I much prefer, soundwise, my complement of connectors than my same cordage with the Oyaides I've evaluated.(but I've no experience with their 20amp versions) I can certainly provide any 20amp IEC you want, but would recommend you first evaluate our standard 20Amp cord.

Paul Kaplan
Thanks for your reply Paul. I hope it didn't come across like I was criticizing your cord, rather it was just an observation as I was thinking of re-terminating one of my own and was looking around at parts.

As I mentioned, your cord does seem to be discussed comparatively in some lofty circles, (both quality and price wise), so I can only assume that you're designing for sound first and foremost and price point is secondary, which you confirm above. It's even better that any savings seem to be being passed on to the customer in the form of a reasonable cost.

If you don't mind my asking, can you elaborate on what sound you're going for with your power cord?

Thank you very much for your time Paul.


Its hard conveying the subjective without having similar frames of reference. If I had to describe the copper/copper or copper/brass 20a cords, I'd opine they are most similar to a Hubbell HBL5362 receptacle, which was actually what I was aiming for; it provides a bit of tonal density and warmth to the midrange, an extended bass and treble, with excellent resolution. The imaging extends back from the speakers and with the proper setup, outside the speakers. The Rhodium terminated cords are more in the vein of a PS Audio PowerPort, but without(IMO) the glare and grit. I'm new to this, and don't know if its OK to even compare my cords to receptacles, and have left out comparisons to competing cords.
I do apologize for this marketing hyperbole, and obviously what works in your system depends on the cord's inherent qualities and its synergy with individual components, as well as your own personal preferences and metrics.

I too am looking for a power cord for my line conditioner so its power cord upgrade time. I'd not heard of the Kaplan PC's before this thread so I contacted the distributor (Tweek Geek). In particular I want to know how the Kaplan compares to Audience and Synergistic Research Tesla.

This was what Tweekgeek had to say:

In general my impressions are:

The Kaplan cables are excellent, I would liken the filtered cords to an Audience Adept response combined with a power cord. The standalone cord really has no competition at its price point of $349.

The filtered cords come in a 3 amp source/pre and 15 amp high current versions. The 3 amp cord actually has double the filtration for more RFI rejection and lower noise floor.

The cords present a relaxed sound, with a layered mid range, deep bass and smooth highs. Soundstaging is very nice. No listening fatigue whatsoever with these cables.

The Audience Power Chord is not as smooth on top as the Kaplans. If you paired an Audience Power Cord with an Adept Response conditioner, you might be getting close to the sound of the Kaplan Cable, but you would be spending a lot more money.

With the Synergistic cables, its hard to say. Synergistic cables work their best when the entire system is Synergistic. They are meant to work that way, as the sum performance of an entirely Synergistic system is more than the individual contributions of each Synergistic cable by itself. I would say you could compare a filtered Kaplan cable to a Synergistic T3 (if you were going to use the cords on an amp).

When you are using only one or two Synergistic cables in your system, its really hard to predict how they will stack up.

Question: Has anyone compared SR Tesla T3 to the Kaplans when powering a line conditioner? Also has anyone ever tried a Tesla power cord and liked it enough to purchase without running all Telsa power cords? What about the Audience PC, are the Kaplans really that much smoother and if so, do they retain detail and air?.

I intend to do a side-by-side comparison but would like feedback from anyone with experience.