SPL - Pro Audio Blasphemy?


In my never ending quest to scale down, I have been looking for a preamp with headphone out. I enjoy passives/buffers and stumbled upon this when I was looking at the Newport Show report on Innerfidelity:

http://spl.info/produkte/kopfhoererverstaerker/phonitor2/in-kuerze.html

Does anyone have any experience with gear that runs on 120v rails? Sounds intriguing, but I plead ignorant. This might seem like a good alternative to the usual preamp and this amp among headphone enthusiast is much revered.

There is also this 2control monitor controller which might be more suitable to my needs because of the flexibility and the ability to switch to mono, but this does not run on 120v rails.

http://spl.info/produkte/monitor-controller/2control/videos.html

Any opinions, ideas or experiences?

Also, has anyone dived into the pro-audio segment for any of their gear as an alternative to traditional hifi?

Cheers
enobenetto
I am using a Tascam LM8-ST line mixer in one of my home systems because I need a lot of inputs and it is all balanced. It has 8 stereo in's and 2 stereo output busses. The versatility is awesome and sound quality is first rate. It sounds every bit as good as a Mark Levinson & PS Audio that I've used as well and it is DEAD quite. I've been a musician all my life (62 Y/O) and am well experienced with pro equipment. I have tried a few pro power amps but was not too happy with them so I stick to home audio for that. Oh I almost forgot, I am using an Ashley 7 channel parametric EQ in another home system and have not observed and degradation in sound. Also I have sold off all of my high end I/C's and spkr cables and am now using Mogami 2534 Neglex star quad I/C cable and Canare 4S11 speaker cable...make'm up myself. All this stuff is considered pro audio and I highly recommend giving it a try.
Sethlover you are on my wavelength!!! (or I'm on yours) I recently started using "affordable" Canare cables and they are awesome and reliable. I see you are using the Tascam in the same way I have been thinking about the SPL, which is inspiring. I feel that the pro gear manuf. wouldn't make a controller that changes the signal in any way or engineers would give them grief and not buy their gear.
Wolf Garcia, it's funny you mention the first watt, because the amp I am using is First Watt J2

Princka, I use JBL 4425 which I did not get at first and then it hit me with proper placement and listening position. This speaker is what made me investigate pro gear for some of the areas in my systems chain.
Ivan, I agree. I actually researched a little to find any power amps that had the 120v but I had little success.
I've personally no evidence that the professional audio market is any less susceptible to changing vogue or irrational expressions of machismo than the high-end consumer market. This fashion of escalating rail voltages has been evolving over at least a decade, IIRC a big influence here was the design and marketing of Solid-State Logic consoles with high-voltage (+/- 90v?) rails.

While I have great respect for SSL and no specific opinions on the SPL gear you mention . . . here are some very specific reasons why I chose to optimize a recent discrete opamp design around +/- 24v rails:

- The requirement for higher voltage imposes some severe constraints on semiconductor manufacturing, and consequently the selection of small-signal parts available to circuit designers really plummets above the 40-60 volt range. For bipolars, lower gain and higher noise is a given to withstand voltages above this range, and there are virtually no matched precision pairs or small-signal JFETs of any type at all.
- The methods for using lower-voltage devices in higher-voltage circuits (i.e. variations on cascoding and bootstrapping) make up some extremely well-trodden ground, and in the best situations the only drawback is complexity. But frequently there are also penalties in noise performance or open-loop response (adding another response pole), the latter means increased distortion, reduced bandwidth, and/or reduced stability.
- Increasing the rail voltages is pretty inefficient at creating additional dynamic range (each doubling of the voltage gives you 6dB). On the other hand it's very effective at increasing heat dissipation, and with higher signal voltages the distortion mechanisms of passive components become much more significant.
- Maximum voltage output with +/- 24v rails can easily exceed 13VRMS, even without special attention to "rail-to-rail" circuit design. This is enough to b!tch-slap the input stage of most any piece of equipment that's likely to follow a preamp, ADC, DAC, EQ, or whatever . . . and that's assuming either an unbalanced, pseudo-balanced, or 1:1 transformer-balanced design. For active-balanced outputs (or a 1:2 transformer) the maximum output is doubled to 26VRMS . . . which for perspective would drive a 4-ohm speaker to 170 watts (if it had enough current of course). By my logic this is more than sufficient for any line-output stage, and if substantially more is required to keep something from clipping inside the equipment, then I need to re-think the equipment's internal gain structure.
- Speaking quite conservatively, a well-designed discrete-opamp line-level architecture with +/- 24v rails can achieve a -110dBu noise floor up to maximum output of 24.5dBu (13VRMS), meaning 134.5dB dynamic range. This exceeds that of a low-noise dynamic microphone (let's say 210 ohms and 1.8mV/Pa based on the industry-standard AKG D112 kick-drum mic) suddenly being moved from an extremely quiet room (15dBa) to a position 50 feet from a jet engine at takeoff thrust (150dBa).

In the end, I felt that setting by the rails at +/- 24V, I could design a simpler circuit that achieved better performance while drawing less power and producing less heat, with no real-world loss in usable headroom. Other designers may of course come to other conclusions for their applications . . . and if they happen to enjoy bragging about how high the rail voltages are on their designs, then they certainly win on that point.