Where does one place AQ sorbogel feet?


I got 3 AQ sorbogel Big feet. These are supposed to reduce mechanical vibration by absorbing energy and releasing it as negligable heat. My question is where under the cdp or amp do I put them. Everyone seems to use them in threes and there are 4 feet. Do I place 2 on the insides of the front feet and 1 between the back feet? Does the flat side face down or up? What do I use to protect cdp and contact points (theyre sticky)? Anyone have experience with these and how do they sound? Thanks in advance!
bundee1
Theaudiotweak: sorry if I wasn't clear. I did not mean that Sorbothane doesn't react to/affect all frequencies. Clearly it must, but it reacts to/affects them differently. Sorbothane absorbs higher frequencies more than lower frequencies. As a result, it lowers the overall system resonance frequency. How a Sorbothane-floated system responds to vibration depends on the frequency of that vibration.

Sorbothane lowers a system's resonance frequency by absorbing vibrations above that frequency. The farther above the system resonance frequency an incoming vibration is, the more of it will be absorbed. This absorbed vibration is largely converted to heat, *not* released later as vibration.

OTOH, Sorbothane tends not to absorb vibrational energy below the system resonance frequency. At those frequencies, it seems to act less like a damper and more like a coupling device.

If you want to lower the natural resonance frequency of a system, (ie, to reduce exposure to support-borne vibrations above that frequency) then the appropriate Sorbothane feet should have reasonably predictable results. This is what I wanted to do with my equipment rack, which is sitting on a suspended wood floor that is easily excited by my speakers. Floating the rack on Sorbothane yielded greater clarity, faster attacks and a quieter background at all frequencies above 30 Hz or so. Frequencies below that, as best I can tell, are slightly amplified but seem about as clear as before. This is consistent with the worksheet on Sorbothane's website, which calculated that I'd have a system resonance frequency of about 28 Hz.

If, OTOH, a component is intended to be *producing* multi-frequency vibrations, as a loudspeaker is, we would predict that placing any vibration damper beneath it would impair its performance. That was exactly my experience with Sorbothane beneath our floorstanders. Attacks were severely dulled. Very bad.

Sorry to Bundeel for highjacking his thread with such a lengthy post. Enjoy the music!
My experience with Sorbothane beneath electronics has been the same as Dougdeacon's beneath speakers. Severely dulled, slow and dark. Sucked the life right out of the music. So if this is what damping is all about then direct coupling is the way to go. Remember your electronics were designed to operate over a much wider bandwidth than the music we hear. There are also harmonics of fundamentals that extend way beyond what we supposedly can hear. If we squelch these harmonics either by accident or by design then we are altering the life of the music. Couple not dampen..Tom's point of view..
Interesting points Tom. I've never bothered to try Sorbothane beneath electronics. Guess I won't!

Putting it just beneath the feet of my rack isolates the components without directly dampening them. A quieter rack must be good. No component is designed to work while being shaken but, as you say, no component is designed to have its own vibrational energy damped either. This has been very helpful, thanks.

We can now explain why, for example, the reportedly excellent Grand Prix Audio racks sound so good (multiple isolation/dampening layers) and also why GPA advises us *not* to isolate or dampen individual components. Let the rack do the isolation, leave the components free to work as designed.

There I go again Bundee1. Sorbothane pucks beneath my TT did isolate it from footfalls. Can't say whether they affected the sound because I've made too many other system changes recently to tell. I'll have to A/B, like you. The discussion above implies I should take them out and let the squidgy bits beneath the rack do the protecting.
Please guys feel totally free to contribute to this thread. You guys are still on topic and Im benefiting greatly from your experiences. Keep this discussion alive, and thanks for sharing.
I may be the old guy here. I have, and am guilty of the following . Making several changes to my system at the same time. My enthusiasm and excitement sometimes clouds my better judgement. I have to temper my emotions and not rush to a premature conclusion. Only one device or one measurement at only one single time, that is the only way to truly measure a change and hopefully an improvement. I will try to remember this. Tom