2. misc-audio
  3. 1086319764

Looking for dedicated power line advice.

I've read just about everything I can find on running dedicated power lines. I met with a good electrician and he is going to run a dedicated line from the main panel to a 6 breaker subpanel with 6 20amp lines to my system. I have lots of questions. Here are a few:
(1) Should all 6 outputs be in the same phase? I've read conflicting opinions. In one of Jonathan Scull's Stereophile "Fine Tunes" columns he suggests that the AC output to a pair of monoblocks should be out of phase. This way noise will cancel out.

(2) Is it worth it to use Wattgate outlets ($150/ea) and will there be audible differences from Hubbel or Marinco or Leviton which would be MUCH cheaper?

(3) Is it worth it to use JPS Labs in-wall cable at $18/ft? Would Virtual Dynamics cable at $6/ft sound as good?? What about much cheaper Romex??

I figure I'm only going to do this once......but I hate dropping a ton of cash unless there is going to be an audible difference.

Thanks for the help!!!
hbrandt
hbrandt's avatar
hbrandt OP
272 posts
 
Lak:

I'm interested in your recommendation that all outputs should be in phase. Jonathan Scull has recommended that consideration be given to wiring monoblocks in opposite phase with the goal of cancelling noise. Take a look at this:

http://www.stereophile.com/finetunes/200/index1.html

I'm probably going to try it both ways.
peterd
122 posts
 
I agree with Lak on the first two points. But reservations though on the 'Virtual Dynamics' Wire.
Did a direct a/b with top quality BX wire and the difference is huge.VD wire was very artificial sounding which is kinda weird since I use a VD Nite, VD Signature and a Audition in my system.Go figure.
Suggestion !. Go to a good industrial supplier, not frigging Home Depot cause they sell the cheapest junk of anyone who will supply it cheapest to them.
Okay then ,Strip off a couple of feet of the 10 guage, 3 wire BX and check it out for discolorations in the copper and the smoothness of the copper. If it is clean and smooth ,no wrinkles, then buy it and you'll be happy.
I learned after trying about 6 kinds /types of wires.
Also check and secure the grounds,in a clean location as far away from any other ground wires.
PeterD
hbrandt's avatar
hbrandt OP
272 posts
 
PeterD:

I'm surprised (and now concerned) to hear of your experience with VD wire. So far, most of the people i've talked to have had very positive experiences with it. Steve Huntley of GNSC told me that several of his customers have raved about it very high-end setups.

Unfortunately, it will be VERY difficult for me to do A/B comparisons of the various wires, so I'm listening to comments like yours very carefully.

Maybe some others will weigh in on this. In particular, I'd be interested to hear if anybody has done comparisions between JPS Labs in-wall wire and VD wire.

Harry
peterd
122 posts
 
Harry,
Well they came across very bright and bodyless.
Ran the wire in for two weeks with two 90watt tube
amps with a PS Audio port . A/B'd with also ran in normal top quality BX,10 guage also.
Absolutely no comparison.
The VD wire was too bright, with no flow to the music at all,attenuated the 'tick- n- pop ' twins really bad.
Found that the same thing happened with my Sim Audio w-5 gear as well.
While it is cheap to buy you can give it a go,but IMHO,
the power cables are great but the in-house wiring does not work.
Peter D .
rushton's avatar
rushton
2,445 posts
 
Hbrandt,

Just one further question for you to ponder: Why the subpanel? By using a subpanel you are inserting another set of electrical connections for everything: positive, neutral and ground. Plus, all of the current for all of your system is being pulled along the one line from the main panel to the subpanel. If the distance from the main panel is not outlandishly excessive, you may have better a result by pulling the 6 dedicated circuits directly from the main panel in uninterrupted runs of cable (provided you have the capacity in your main panel to add the breakers you need.
.
More to discover