Say it aint so--- Teres quality question


As a preface-- I have been a lurker here at Audiogon for a number of years, but have never posted.

Yesterday a review of the Teres 200 series table was posted at Audioasylum. I am extremely concerned about what was stated.

I have always read fantastic things about the Teres, but this reviewer seemed to consider some issues with regard to quality-- ie:

"Some minor issues...the wood platter is not 100% true on the horizontal surfaces...a very slight rise...I suspect this is the nature of machining wood?" as well as "Product Weakness: Platter slightly off true"

I plan on joining the Teres family -- but have developed some reluctance after reading this.

Perhaps some of the members here with first hand experience will be able to put my concern at ease with regard to the reviewers statement.

Here is a reference to the post:

Review by Angus Black III on January 06, 2004 at 10:35:32

Thank you, and a special thanks to TWL for the always informative reading.

Focusedfx

128x128focusedfx
Angus Black's Teres Review mentioned above

He doesn't seem to upset about it. He says " The table just continues to amaze day after day" and calls the other stuff minor issues. I've never seen any audio product (or any product for that matter) that got all perfect reviews.

I do wonder about how wood platters will hold out over a decade or so. If you control the humidity I would think it would be ok.

If it really bums you try an Acrylic Platter. You notice how many of the hardwoods are out of stock at their site.
I feel a little guilty about using exotic hardwoods these days.

Cheers
I remain,
Yes, I can see that this does not seem to bother the reviewer-- but if it were MY table I would be very upset and unable to dismiss this with an "oh well, BTW".

Hence my post.

Thanks for your reply,

FX
As a former apprentice who graduated from the expert tutelage of my master craftsman grandfather, I have had misgivings with respect to wooden platters.

On the other hand, several Teres users, and the Man himself, posted at some length on this topic on this board not so long ago (suggest a search). Teres believes that it has sufficiently considered and addressed the "woody" issues.

In the end, you have to weigh your decision based on all the information you can find and then act accordingly.
The bearing, motor and speed controller are top drawer. The plinth, platter and armboard design is simple which is a good thing. However, I noticed the same woodworking issues with this 265 plus a couple more. The armboard that was supplied was almost 42 mm tall as opposed to the specified 27 mm. This dimension is not posted on the Teres website as far as I could tell and only found this out after prolonged correspondence. Of course, this has caused a lot of stress trying to establish VTA. Hopefully this will be resolved soon. The armboard bolt that was supplied was much too short. The mating surfaces of the plinth/armboard exibited a lot of daylight which led me to check the top and bottom surfaces of the armboard and what I found was not good. These sufaces are not flat and is very visible with the naked eye in every plane, ie; length, wide and diagonal. The holes that are drilled for the tonearms are done with Forstner bits of inch increments. Since tonearms are fabricated in metric and Forstner bits are readily available in metric sizes I wonder why they don't use them. It would make fitting the VTA collar to the hole a much easier and cleaner job. The irregular wooden surfaces are the result of running short pieces through a planer plus sanding techniques. It's the nature of the process. The platter with this table is cupped from the outside toward the spindle by a considerable degree (perhaps 1/8") but seems to rotate true. I may have a slightly biased opinion about this type of manufacturing that is in disagreement with the manufacturer. I realize that you could take a coffee table and drill three holes in it and probably have a great table but I expected machined surfaces. That is what they say in their description of the platter although the pictured platter is acrylic. Once you get your hands on one of these you understand that there is very little that is critical dimensionally. The holes need to be perpendicular to the plinth. The armboard surfaces need to be parallel to the platter. Of course, the armboard needs to be close to the correct height. Cocobolo may be the best thing that ever happened in the analog world and I doubt that warpage or delamination will ever be an issue BUT I feel strongly that the surfaces should be machined in a mill. I'm not a happy camper and this isn't my table. I did recommend it though and feel very bad for that but I'm also confident that it will be fine in the end. For my money I would buy the bearing and motor/controller and build my own. Perhaps the worst part of this whole thing is writing these words. I hate to do it and I fear I may become very unpopular very quick. I do have photos to back up my claims.