How do you deal with vibration?


Greetings all,

Many of us work very hard to keep vibration out of our equipment. I was hoping we could share our experiences with each other. I was wondering what other DIY methods people are using?

I personally have had good luck with shipping open cell foam under plywood. I find that about 60-70 percent compression works best. I place the foam underneath some plywood (Using spruce 3/4 inch). Then I place the component on the plywood. However, I think this more isolates the component from outside vibration. I don't think it does much to drain internal vibrations, especially in a CD transport.

Also I can not find open cell foam in town any more. I am ashamed to say that I actually went to Wal-mart to buy some. Now they don't carry it any more. So I was wondering where else I can get some?

I am currently thinking about building a Sandbox for my CD player and amp. Then putting the sand box on top of some sort of isolation material (open cell foam or cork rubber etc.) My thoughts are the foam or cork or etc should help keep the vibrations from getting into the equipment and the box should drain the internal vibrations.

Also, what are peoples experience with different woods. I live in BC so I can get most wood fairly cheap. I imagine every wood has it's own sonic signature due to it's resonant frequency. What works best? Solid maple, birch ply, MDF, walnut, mahogany etc...?\

Anyways, feel free to through ideas and experience (both good and bad) out there. It would be good to know what works and what doesn't.

Happy tweaking,
Nick
nickway
>>I was dubious about vibration<<

>>my Shanling CDT 100 was already on an acrylic stand on vibrapods and that on a Hutter rack.<<

You couldn't have been that dubious, you were already a consumer of vibration control products and were out purchasing more.

In any case, former skeptics with conversion stories are not uncommon in religion, paranormal phenomenon -- and audio.
Basically what I am wondering is:
What DIY platforms work best for each component?

IE:
Does a sandbox or a DIY symposium (or other) work better for CD players?
What works best for amps?
Turntables?

Thanks,
Nick
Pbb, What I'm actually saying is that I feel that there is no need to debase someone else's beliefs. Other than some ego satisfaction you might gain, it serves no purpose.

Personally, I would feel just as comfortible saying "based on my experience I could hear no differences when solid state devises were isolated from or coupled to other surfaces" and then go on to speak to how I would treat vibrations as they relate to tube products and turntables.

The poster wanted to talk about DIY vibration control techniques and materiels. I didn't note that he asked for any opinions about the efficacy of such controls.

There are a lot of things out there that a lot of folks feel good about believing that can't be explained or even proven to exist. Start with God. With your mentality I could visualize you going to church to proclaim to the folks in prayer that they were wasting their time, that no one was listening.

Now since Nickway has reposted, and your post implied that vibration controls can be effective for TT & tubes why not sieze the opportunity and share your experiences on how to deal with these components. That would be a nice positive thing to do.
Newbee,

I don't mind other poeple posting their comments. By all means feel free.
I just did not want my question to get lost.

Cheers,
Nickway, FWIW, I have achieved the best results in DIY isolation products for components and turntables, much the same way as you have, by using a sandwich of materiels, usually a soft wood and a medium density foam product. What I use depends on the sensitivity and the weight of the component, but my purpose with all components is to prevent incoming vibrations and to allow the vibrations from components (either airborne or self generating (as in CD players) to flow to a substance that is absorbent such as soft wood. Unlike others I don't subscribe to hardwoods or stone products, and I usually want the mass of the vibrating component to exceed the mass of the substrate. IMHO sandboxes can work just fine with the sand taking the place of the foam product. FWIW, except with ultra sensitive equipment, I don't believe in fussing too much about this process. Much of the damaging vibrations your system will experience are airborne and most the damage is done before the vibrations reach the control devise. The cost of materiels is relatively cheap and its a fun Saturday project in the workshop. :-)