Great advice slaw! Thank you very much
Best building material for vibration free shelving
I am building some built into the wall shelves for my VPI Classic 2 SE turntable, amp, preamp, CD player, and old Burwen TNE 7000A transient noise eliminator (that’s one for you old-timers to remember), as well as my DISH Network receiver box. The shelves must match in appearance the typical looking built-in wood bookshelves already in the room. The shelves will be located directly under my 45" wide flat screen television. They will be wide enough to hold two components side by side, other than the VPI turntable which will have the top shelve to itself due to its extra width. I will be building the shelves high and deep to allow for plenty of air circulation around the components. They will be painted.
My question is, what materials might you suggest building the shelves with to minimize vibration? If they were for books I’d normally build the sides, and top out of 3/4" birch sided plywood, the back out of 1/4 inch luan plywood, and the shelves out of oak to deal with the weight of the books without bending. I will be adding vibration damping feet under each component and am not looking for suggestions along those lines, only material and perhaps design recommendations to reduce vibration.
I was researching this last night online and on site, and saw recommendations to use four thicknesses of 3/4 inch High Density (HD) MDF, also to use granite or marble under the turntable, among other recommendations. I was wondering how birch veneered plywood would work too, as it’s ply’s, I believe, have their grains running in opposite directions. Maybe there’s some way to isolate the uprights from the horizontal shelves to reduce vibration transmission.
What would you think would work best for these built-ins. I’d appreciate any recommendations you have or your experience on this subject. Thank you for any ideas.
Mike
My question is, what materials might you suggest building the shelves with to minimize vibration? If they were for books I’d normally build the sides, and top out of 3/4" birch sided plywood, the back out of 1/4 inch luan plywood, and the shelves out of oak to deal with the weight of the books without bending. I will be adding vibration damping feet under each component and am not looking for suggestions along those lines, only material and perhaps design recommendations to reduce vibration.
I was researching this last night online and on site, and saw recommendations to use four thicknesses of 3/4 inch High Density (HD) MDF, also to use granite or marble under the turntable, among other recommendations. I was wondering how birch veneered plywood would work too, as it’s ply’s, I believe, have their grains running in opposite directions. Maybe there’s some way to isolate the uprights from the horizontal shelves to reduce vibration transmission.
What would you think would work best for these built-ins. I’d appreciate any recommendations you have or your experience on this subject. Thank you for any ideas.
Mike
- ...
- 129 posts total
Oops - I think I may have missed responding to a couple of people ... @n80 ... williewonka, I made some feet for my preamp out of walnut that I had lying around. The rubber feet of the pre-amp sit in the little divots on top, the wood blocks sit on 1/4" sorbothane pads. Does any of this make any difference? I have no idea. Kind of doubt it, but total cost was about $12.I originally had sorbothane on some DIY feet I positioned under the components foot, but after trying the same feet placed directly under the components case I found the image became much more focussed and larger, with more clarity @skyscraper... Steve (Williewonka), After reading your suggestion, I might try using my piece of leftover marble, and set it on the top shelf under the turntable with a piece of tool drawer liner, or constrained layer damping in between, once I figure out what that is and how to get it., Thanks for your ideas. There is a company that builds shelves for components racks that utilize the constrained layer damping for their shelves made from foam filled stainless steel - but I have forgotten their name. Here’s one that makes complete racks http://www.symposiumusa.com/mysrack.html But since I am all about using an affordable DIY approach I found the tool drawer liner "sandwich" approach to be very effective - but the above rack does look very nice :-) I also take a similar approach with my speakers because they are on carpet... - Speaker has cone feet and sits on a ceramic tile - then a layer of drawer liner under the tile - then a granite tile with one of the multispiked carpet protector feet at each corner https://www.amazon.ca/Spiked-Plastic-Caster-Short-Carpet/dp/B000VYHCYM/ref=sr_1_cc_1?s=aps&ie=UT... I didn’t want to allow the speakers coned feet to penetrate the carpet/underlay It is a very stable solution once the carpet and underlay compresses, which takes about a month - my speakers weigh around 50 lbs each WRT cone feet - I have had a chance to experiment a little more and found the position of feet makes a difference e.g. - my amp has a foot either side of the large transformer and the third foot positioned for optimum stability - my phono stage has one foot under the transformer, another under the circuit board and the third foot positioned for optimum stability - My Turntable - was a little more complex - please see
I only use three feet - for stability The larger feet are not attached to the component - the component simply rests on top of the cones The smaller feet however, are attached with a piece of double-sided tape. Hope that helps - Steve |
Slaw, I'm going to build the shelving like described earlier in the thread and use under the marble for the turntable shelf, some constrained layer damping. Sorry for the late response, but this thread did get away from me. Still not sure what to use between the tops of the metal clips holding up the shelves and the shelves themselves to dampen vibration, maybe some leftover scraps of the constrained layer stuff. Thganks for asking. Mike |
- 129 posts total