2. amps-preamps
  3. 123816-10404

Best Way to Spend ~ $2000 for System Improvement

Hi fellow music lovers! I have about $2000 right now to improve my system. It can be for any component, but I'm thinking amplification first, power, pre, or integrated. SS or tube.

To begin, right now I have a Mccormack 0.5 Deluxe power amp with "A" revisions, an Eva 2 passive preamp, Metrum Octave v1 DAC, Dell laptop for music files. Sometimes I use a Teac H750 as a transport and GMA Pico Executive speakers. The room is small, about 14x18x10ft. I listen to about 50/50 rock and classical, mostly full orchestral. As far as just sound goes, I would like the bass to be "fast". No delay or overhang, not exaggerated, but detailed. Detail is important at any frequency, the more the better, but not at the expense of musicality. I realize at this price point, compromise is necessary, and treble would be the best place for that. No harshness allowed, but I'm in my later 50s now and don't hear treble like I once did.

I hope I've given enough info to get some good suggestions. I like the sound now, but think it could be better, maybe a slightly lower noise floor and a little more pace and rhythm while retaining it's sweetness and smoothness. Any advice would be greatly appreciated. Thanks in advance. BTW, if any existing question answers any part of this question, feel free to link it.
xrayz
lowrider57's avatar
lowrider57
5,417 posts
 
@xrayz, 6 years ago, an electrician charged me $210 to install a 20 amp breaker and run 12 gauge Romex from my basement panel to the 1st floor. I've since learned that 10 gauge is recommended and that I really needed 2 dedicated lines.
Running two lines at the same time would be very cost effective. Most electricians will give you a free estimate for the work involved, although you may need to supply the 10 gauge Romex since it's not a standard size for a residence.

For AC receptacles, Porter Ports are highly recommended and sold by Audiogon's Albert Porter. And very affordable.
https://www.audiogon.com/listings/ac-distribution-porter-port-porter-ports-outlets-cryo-various-colo...
passet02's avatar
passet02
267 posts
 
Speaker and interconnect cables will do it .Will not get tired or change them every 2 years
danvignau's avatar
danvignau
935 posts
 
There is a lot of disagreement on this site, but I still say that an amp with a high damping factor has tighter bass. Check out the match between Audire Forte and B&W DM 16 omn the site listed below.

I have tried a lot of amps, including giant Classes, and these speakers require a lot of control, i.e. they need the amp to stop as well as start them.

I use the woofers as subs for my 803's, at least on loud rock.  
danvignau's avatar
danvignau
935 posts
 
Whoops:    http://www.avsforum.com/forum/91-audio-theory-setup-chat/1243132-hall-fame-audio-equipment.html

I am not suggesting anything except that a high damping factor gives tighter bass.

The 350 wpc Classe does not compare with my 125 wpc Forte, and all other Audires after the Forte (which followed the Model 1 and 2, Crescendos, and Forte) are even better, and have even higher damping factors. 
xrayz OP
105 posts
 
@lowrider57  Those prices are really good, especially since my circuit breaker is exactly under the stereo. I always wanted dedicated circuits to see if I could hear a difference in the sound. If I may ask, is Romex generally recommended? Also, is there anything else I should tell the electrician? I mean, I doubt the average electrician knows much about sound. Or is everything I need to know already in the A'gon  discussion files? @passet02  Do you have any specific ones you like? I could always use recommendations! @srosenberg  I'd love to try a Modwright, I've always heard great things about his equipment! Pass too! There's a lot I'd like to try, maybe even older vintage Threshold. Also, my speaker manufacturer uses Atma-Sphere electronics at CES they go so well together. @almarg  I meant to respond before- I do use coaxial to connect with both my pc and cd transport. My octave v1 has no usb input. In your opinion, even if the impedance matching is not a problem, would a better usb/spdif converter go a long way toward solving the perceived lack of dynamics? I've only ever used this one, and I know a lot of people consider them to be one of the most important components, paying a huge amount of money for their own.              
More to discover