Cartridge Loading- Low output M/C


I have a Plinius Koru- Here are ADJUSTABLE LOADS-
47k ohms, 22k ohms, 1k ohms, 470 ohms, 220 ohms, 100 ohms, 47 ohms, 22 ohms

I'm about to buy an Ortofon Cadenza Bronze that recommends loading at 50-200 ohms

Will 47 ohms work? Or should I start out at 100 ohms?

I'm obviously not well versed in this...and would love all the help I can get.

Also is there any advantage to buying a phono cartridge that loads exactly where the manufacturer recommends?

Any and all help would be greatly appreciated.

Thanks in advance.
krelldog
As the Ortofon is a fairly low output MC cartridge there are generally two components to the frequency response which interact.
1. The electrical LCR response.
Contrary to what has been said, for LOMC the capacitance, unless it is quite large (in the order of .1uF), is essentially irrelevant and the objective is to set the response to look like a single pole LR system.
See the MC cartridge section in this article.
http://www.hagtech.com/loading.html
In most cases a resistance close to 100 ohms is fine- largely because the coil DC resistance is often a proxy for the inductance (most cartridges have a similar internal magnetic structure) and turns out to be close to 5 ohms and c.0.5mH, (There are exceptions- Miyajima cartridges are a good example of this) and as a result a 100 ohm load gives you a well damped electrical system (no peaking) with a bandwidth of c.35kHz. This results in c. 0.3dB attenuation at 10kHz and c. 1.1dB at 20kHz. You could try to flatten the response out a bit by greatly increasing the cap, but it’s tricky and usually impossible because of the tip/cantilever/suspension resonance. 
To illustrate this point, use the Hagtech calculator and set the capacitance to 200pF and the inductance to 0.5mH- the resonance is at 500kHz and into a 47k load the Q is c.30!  To reduce the resonance to 50kHz the cap must be increased to 20nF and the Q (R/inductive impedance) becomes 300! If the load R is reduced to 100 then the Q is 0.06 for the 200pF cap and 0.6 for the 20nF cap.
So, clearly a low load R reduces the electrical system to a simple, single pole RL form.
2. Tip/cantilever/suspension resonance.
Typically this looks like an electrical equivalent LCR resonance plus an additional HF pole. I wont go into the math, but it’s not unusual for this to have a resonant peak in the high sonic/supersonic range- 18-40kHz, and with an amplitude of 2-6dB at the peak. This is NOT the electrical resonance and cannot be corrected for by changing the loading of the cartridge. It can be modelled as an LCR plus an RC followed by a unity gain buffer or as a mismatched transmission line.
Essentially the cantilever flexes and resonates when stimulated by the movement of the stylus tip and the response is damped by the suspension/coil dampers.
So, the bottom line is- you’ll never get it perfect. You can either listen and decide what you like, or use a test record to check the sonic response. A couple of other things, the RIAA deemphasis of your amp comes into play, and it’s not unusual for that to be off c. 0.5dB or so over some frequency range, and most amps have restricted frequency responses to reduce the infrasonic and ultrasonic signals.
Also, your room/speaker response is probably poor with errors at least as large as any from the above sources, so unless you’ve characterized and corrected that then listening is probably your best bet.
Wynpalmer4 5-25-2018
Contrary to what has been said, for LOMC the capacitance, unless it is quite large (in the order of .1uF), is essentially irrelevant ....
As explained earlier by me, and by Atmasphere (Ralph Karsten of Atma-Sphere Music Systems), and in the statement I quoted by Jonathan Carr (Lyra cartridge designer), while load capacitance is indeed essentially irrelevant to the cartridge, it is not irrelevant to phono stages whose design is such that RF frequencies received at their inputs can have audible consequences.

Regards,
-- Al
I may not be a renowned Audio Designer, but I am a somewhat renowned IC designer with credits that include cell phone transceivers and high performance opamps. 
In truth, the issue with phono stage RF has little to do with the capacitance loading- rather it's that many RIAA stages are designed to be non-inverting and lack the additional pole necessary to provide attenuation at ultrasonic frequencies and above. For example:
http://audiokarma.org/forums/index.php?threads/ad797-phono-stage-build-and-help-desk-thread.501186/p...
Where I discuss this very problem as an aside to optimizing an opamp based phono stage.
The non-inverting amplifiers used in an RIAA stage never have a gain below unity unless an additional pole is added. It's hard to see why adding a capacitance of significant value to the input of a phono stage helps when the self resonant frequency of most larger value caps is well below the RF region of interest. Indeed, if that is your concern, then adding several caps of scaled value 1-2 orders of magnitude apart, say 0.1uF//3300pF//100pF as the cartridge load would be the way to go, and who does that- except as an extra pole in a non-inverting RIAA stage.
I'm a believer in fixing the problem where it exists and not by adding an additional parameter to an already over-constrained problem.


I have my Nova II phono pre capacitance set at 100pF for my Delos and I use an AQ Cougar phono cable with total cap at 60pF. Lyra suggests using the lowest cap cable you can, and for me it does make a difference, as I was using a very high cap cable in the 350pF range with loading at 121 ohms.
The dynamics and resolution is so much better now.