2. misc-audio
  3. 1375840071

Does it bother you?

I'm a recording engineer who has worked in some of the world's top facilities. Let me walk you though an example signal path that you might find in a place like, say, Henson Studio A:

1. Microphone: Old. Probably a PCB inside. Copper wiring.
2. Mic cable: Constructed in house with $1/ft Canare Star Quad, solder, and a connector that might have been in the bottom of a box in the back.
3. Wall jack: Just a regular old Neutrik XLR connector on the wall.
4. Cable snake: Bundles of mic cables going to the control room.
5. Another XLR jack.
6. Another cheap mic cable.
7. Mic preamp: Old and lovely sounding. Audio going through 50 year old pots.
8. Patchbay: Another cheap copper cable is soldered into a patchbay where hundreds of connectors practically touch.
9. TT Cable: Goes from one patch to the next in the patch bay. Copper. No brand preference.
10. DB25 connector: Yes, the same connector you used to connect a modem to your computer in 1986. This is the heart and soul of studio audio transfer.
11. DB25 cable to the console: 25 strands of razor-thin copper wire, 8 channels of audio, sharing a ride.
12. The mixing console: PCB after PCB of tiny copper paths carry the audio through countless op amp chips.
13. DB25 cable to the recording device: time to travel through two more DB25 connectors as we make our way to the AD converters or tape machine.
14. AD conversion: More op amp chips.
15. Digital cable: nothing fancy, just whatever works. USB and Firewire cables are just stock.

...and this is just getting the audio into the recorder.

Also:

None of this equipment has vibration reducing rubber feet, it's just stacked haphazardly in racks. Touching.

No fancy power cables are used, just regular ol' IEC cables.

Acoustic treatment is done using scientific measurements.

Words like "soundstage" and "pace" are never uttered.

Does it bother you? Do you find it strange that the people who record the music that you listen to aren't interested in "tweaks," and expensive cables, and alarm clocks with a sticker on them? If we're not using any of this stuff to record the albums, then what are you hearing when you do use it?
trentpancakes
jjrenman
279 posts
 
Trentpancakes,

A reason for the better sounding recordings of the 50's and 60's may be that there is a lot less of all the little "problems" you mention in rant.
onhwy61's avatar
onhwy61
5,216 posts
 
Excellent question. One that should be taken seriously.

In direct answer to your question I say Yes! It does bother me in that studio wiring and connectors can be easily improved at fairly minimal cost. So much of the wiring in a studio is done for convenience as opposed to sound quality.

What Trentpancakes doesn't say is that you can still make good sounding recordings in these studios. It's easy enough to bypass most studio wiring, consoles and patchbays and go direct to the recorder. Many engineers bring a handful of "special" microphones and mic pres with them to a session. Skillful engineers can assess what they have to work with and adjust accordingly.

What I think audiophiles don't understand is the engineer's primary job is to capture a good performance. The studio can be a chaotic place where the sound engineer is not the man in charge. People can be milling around, eating pizza, the girlfriends are comparing shoes, the singer's on the phone, the producer is out of the room and the guitar player is just messin' around with some chords and he'll suddenly bark into the mic, "did you get that?". In that hectic environment a good engineer has decent sounding tape of what the guitarist was playing.

When all is said and done when a studio/producer/engineer does adopt audiophile standards, I'm thinking Mapleshade, you do get better sounding recordings.
jjrenman
279 posts
 
I can make an argument that 10 of your 15 "issues" were not present in those early recordings where simple recording techniques were used.

Excellent recordings are like a fine restaurant. You have to go out of your way to find one created by those who truly care enough about the final product to pay attention to every possible detail.
trentpancakes OP
13 posts
 
A reason for the better sounding recordings of the 50's and 60's may be that there is a lot less of all the little "problems" you mention in rant.

That simply isn't something that's supported by fact.

Equipment in the '50s and '60s was marked by its high THD, noise, microphonics, and nascent electrical engineering. Signal chains, instead of having loads of DB25 interconnects, had multiple generation losses on tape decks with, by today's standards, abhorrent specs. Almost every piece of equipment in the chain was a tube device that added multiple odd and even-order harmonics (which is actually perceived as pleasing to the ear, although it is, by definition, distortion).

The entire philosophy of '80s recording and engineering was to clean up the signal path of the '50s-'70s, which was considered to be extremely low fidelity.
trentpancakes OP
13 posts
 
When all is said and done when a studio/producer/engineer does adopt audiophile standards, I'm thinking Mapleshade, you do get better sounding recordings.

Thanks for the reply, and it does accurately depict what goes on in a studio. It's controlled chaos, and it's about getting a creative spark on tape FAST. There's no time to obsess over a signal chain. Take "Something in the Way" off of Nevermind, as a rock n roll example. Kurt starts strumming the song on the control room couch, and he's killing it. It sounds perfect. So Butch scrambles and throws a mic in front of him right where he's sitting, and they captured perfection. If he had stopped to employ some audiophile aesthetic, it would have been lost.

Of course studios and engineers who specialize in audiophile recording are going to produce clean sounding records. It would defy reason to say that they don't.

But it still doesn't explain how audiophile listeners only seem to find extreme positives when they listen to traditional studio recordings on expensive stereos. It's all about "big soundstages" and "less smear" and "livelier pace." It's never "revealed more noise" or "heard tuning problems" or "hum was more pronounced" or "soundstage stayed the same."

How are you getting good things that we don't hear, but aren't hearing the bad things that we DO hear?
More to discover