Geometry for pivot tonearms - calculation errors??

Dear Dertonarm: Could you share your " finds " /thoughts n that 1st geometry for we can understand and try to help about?, because both have an intimate relationship.

Regards and enjoy the music.
Raul.

Dear Raul, - let me put it in a few "axioms":

1) offset, overhang and effective length do relate to each other and CAN be CHANGED WITHOUT changing the PIVOT-BEARING DISTANCE. Offset, overhang and effective length do change when you align to a different arc-calculation (say - change from Baerwald to Loefgren).

2) If you change the pivot-bearing distance you change the WHOLE GEOMETRY of the given tonearm.

3) you usually get the very best results with the recommended pivot-bearing (= mounting distance) as specified by the manufacturer, because the whole geometry of the given tonearm builds on that one parameter.

4) whether you choose Loefgren, Bauer, Baerwald, Stevenson or whatever calculation for the alignment of the stylus (and these calculations are onyl aiming at the position of the stylus - not at the position of the tonearm !!) is INDEPENDENT from the geometry of the tonearm itself. These alignments can all be done at the headshell alone without moving the base (and thus the pivot-bearing distance). And they should be done without moving the base because that way you can be sure that the basic geometry of your given tonearm is as specified by the manufacturer.

I think we must clearly put a line here between the geometry of the tonearm WITHOUT a cartridge.

This is the basic geometry of the tonearm itself = 1st geometry.
This is step 1.
Then there is the geometry of the stylus in a given tonearm = 2nd geometry. This is step 2.
Here we have the option to align to whatever calculation does fit our needs best (for instance more modern pressings with long run-out-grooves or pressings from the early 1960ies with the inner grooves running close to the label - these need different alignments - one rather Loefgren - one rather IEC). Here we lay the position of the 2 zero-error points and the maxima and minima derivation. This 2nd alignment does have variations in the offset, overhang and effective length (not much, but some) - but NOT in the pivot-bearing (mounting) distance.

Thank you for your direct email. I will put together a few "basics"/standards for LP-quality and will email to you in the next 2 days.

Dertonarm, How then do you feel about the SME tonearms, which utilize a sliding pivot point in order to achieve pivot to stylus adjustments? In the process the pivot to bearing or spindle distance is also altered pari passu.

Dear Lewm,
the SME 300 series (including SME V and IV) is one of the very few tonearms which does come with a kind of "fixed" geometry in ALL parameters. Given its unability to adjust offset, overhang (we can just move the base - which we shouldn't... - NOT the cartridge ) and effective length, it surely is a fairly unique sample.

Make no mistake - the SME V was designed for a specific mounting distance spindle to pivot-bearing! The SME sliding base is often mistaken for being an "invitation" to "adjust" the base "freely" to whatever alignment you want.

Not so.

SME does specify a mounting distance of 215.35 mm.
See here:

http://www.sme.ltd.uk/content/Series-V-1330.shtml

They did not give this very precise figure out of the blue........

SME took for granted all industry standards of its day (early 1980ies) and said:

"well, if all cartridge designers do obey to and follow the standards given and if all LPs are cut following the new IEC standard, then evrything will be perfect with our new tonearm - it will be the "best tonearm in the world"............"

But the world is an imperfect one and many people do want to go their own ways.

The new SME surely was the LEAST UNIVERSAL tonearm ever designed .......
It is for sure the one tonearm which gives almost no possibilities to adjust to specific cartridge needs or to different arcs.

The SME V was a child of its day and was regarded when introduced as the first tonearm which took all (some of them fairly new...) industry standards for record-cutting and cartridge dimensions serious.
Too serious.

Only a cartridge with 100% orientated cantilever and 100% standard horizontal distance mounting holes-stylus can be correctly aligned in a SME V and can only be aligned to ONE standard cuve/arc - the IEC.

Offset can not be aligned in an SME - thats why the SME template does FORCE the user into one possible geometry only.
Thats why the MINT tractor is so very effective with a SME V and a specific cartridge.

In a biological sense the SME V (and its offsprings with fixed headshell and fixed mounting holes) is the very opposite of evolutionary versatile.
It can not "adjust" to any change in the "enviromental conditions".
With the "right" cartridge, it is a VERY serious tonearm.
But there are so very few "right" (read: 100% following IEC standards) cartridges for the SME V around.......

Howdy,
here me meet again.
Just been thinking about Dear Lewm's input, which makes me think to start a thread for the 'poor' V owners i.e. which carts are a GOOD/BEST fit?

I guess we'd mostly look for MCs despite Raul's most extensive experience in MMs.

The cart stylus to mounting hole distance IEC-standard? is in any case to be 9.5 mm for the V arm.
DerTonarm will want to know it a bit more down to the 100th mm so we'll call it 9.52 mm (actually 5/8"). Now for me that begs the question why ICE would have settled for inches?! The mounting hole distance of 1/2" is also not quite metric, now is it?

What do you think? There'd be some folk to give some best fit input?
I use a Windfeld as you know --- and I would not add that to the list of BEST FIT! Amen. Sound great, but not BEST FIT in the alignmnet sense, methinks.

What else can a V owner do? You have mentioned all's fixed, can't even mess around with different flavours A, B, Stevenson...
It's vanilla SME, or go buy some other tone-arm, right?

Best greetings,
Axel