Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
George built one for me a couple of month ago. It is by far the best attenuator I have ever used in my system.
Great depth and open soundstage.
Very lively with tons of attack.
Thank you George, the Stereophile recommendation is spot on.
John. (JW Audio)
For those who want an integrated amp or preamp with a LDR controlled type of volume control in the designs.
The Japanese company Arte Forma Audio have used (I'm not sure if correctly used) a form of the Lightspeed Attenuator in their Susan and Susan MkII integrated as well as in their Perla preamp.
Correctly they have refrained from inserting it into their tube products, because they probably have found that the fluctuating heat environments within tube products leads to an LDR type volume control not be able to stay in calibration.

Cheers George
George, are you saying that a DIY guy like me really cannot place an LDR volume control in a tube preamp. It would be interesting to compare to a nice Shallco stepped attenuator.

Would LDR actually sound better then a Shallco in a top notch active tube preamp. Interesting idea. You seem to think the heat in a tube pre may cause problem?
Anyone can put one in a tube pre or tube power amp, but the temperature fluctuations will make it go out of calibration very quickly.
Comparing the Shallco to the Lightspeed in a preamp where there are no switches or balance controls, in other words no other switch contacts that the signal has to travel through. The Lightspeed will sound better than the Shallco.

Cheers george