2. digital
  3. 1327433514

Listing of Opamps for EE Minimax DAC Plus

Phil from Cimmaron Technology sent me a list of approved Opamps for
respective positions on the board of the EE Minimax DAC Plus; prices
include the Brown Dog Adapters provided by Cimmaron. I have been using
in the U1/U2 position the OPA2604 and in the U6/U7 position the OPA827.
I have not Opamp rolled this unit much, as I have been busied with other
components for review. I attest that the DAC Plus in SS output with the
tube removed and these opamps is sensational.

(NOTE CAREFULLY the warning at the bottom NOT to use the AD 8620 in the U1/U2 positions!) Also note that the positioning of the opamps/adapter is always with the small square solder point on the topside of the Opamp at the upper right hand when the unit is facing the installer. Finally, it is recommended that an opamp extraction tool and an anti-static device be used when removing/installing Opamps.

Is it "worth it"? YES! YES! YES! :)

RECOMMENDATIONS OF OPAMPS FROM CIMMARON TECHNOLOGY:
For U1/U2
Single-channel op-amps mounted on the 020302 SO8-to-DIP8 single-to-dual
channel adapter:
qty 2 each required

020302-OPA627 $48.00 x 2 = $96.00
020302-OPA827 $38.00 x 2 = $76.00
020302-AD797B $48.00 x 2 = $96.00

. . . also for U1/U2
Dual-channel op-amps mounted on the 970601A SO8-to-DIP8 adapter
qty 2 each required

970601A-AD8620 $23.00 x 2 = $46.00
970601A-OPA2604 $13.00 x 2 = $26.00
970601A-OPA2134 $10.00 x 2 = $20.00

For U6/U7
Single-channel op-amps mounted on the 970601A SO8-to-DIP8 adapter
qty 2 each required

970601A-OPA627 $28.00 x 2 = $56.00
970601A-OPA827 $23.00 x 2 = $46.00
970601A-AD797B $23.00 x 2 = $46.00

The AD 8620 should not be used in the DAC PLUS.
"On some forum there was a suggestion to use the AD8620. for positions U1
and U2. While this is a dual op-amp, it is only rated to use up to
plus/minus 13 volts. The circuit in the EE Mini Max DAC and DAC Plus is
plus/minus 15 volts."
douglas_schroeder
sibelius
256 posts
 
I've not heard anything definitive from EE, but one theory is that the power supply would see less of an overall load and perhaps lower noise level on power rails to opamp.

Whatever the reason, I've tried the tweak and do find it an improvement.
josefm
53 posts
 
Same* result here, SS output is much improved with tube removed...however, with the right tube (system compatibility) I prefer the 'fleshier' output of the tube stage.
I found no real measurable (by ear)improvement to the tube output with the removal of the SS opamps. My guess would be that the tube stage draws more juice from the p/s vs the SS output opamps.
morningstaraudio's avatar
morningstaraudio
154 posts
 
Skomak,

I was concerned also and wrote Alex again just to double check. His reply;

Hi Bill,

The DAC Plus has enough current supply for four Burson opamps.

Hope the above helps.

Thanks.

Best regards,

Alex
sibelius
256 posts
 
I've been experimenting some more with opamps and have to say that the only combination I like a tad bit better than what Doug recommended (2604 in U1/U2 and 827 in U6/U7 with tube removed in SS mode)is to replace the 827's with Dexa discrete opamps. I'm finding the discrete opamp seems to add a bit more air around the instruments while making things a tiny bit warmer. However, the cost of the discrete opamps is rather high and the difference is not night and day. I think the 2604/827 combo is probably the best mod for the $.

I'm going to try two more experiments. The first is to go back to tube mode with a NOS mullard 12AU7. The second is to add Dexa discrete opamps in U1/U2 and see how an all Dexa system works.

More to come ...
skomak
4 posts
 
Thank you Bill

Very proffesional from your side
Rgds
More to discover