The OP did not rule out changing the stock tubes as a small change. I experienced a very big change using the electrically equivalent 12AX7 stock tubes in a Jolida CDP output phase for 12AX7 Mullards. Both sets of tubes were close to new so it wasn't a burn in vs non burn in issue and a 12AX7 is a 12AX7 isbn't it. Anyone was able to hear a big change in the sound for the better of course.
One Small Step ... That Transforms Your System
I just had an interesting thing happen to my system that I wanted to share.
I use PCs, SCs and ICs in series. I have talked about this in other threads and will not restate this here. Some of the patch wiring I use is Supra LoRad that I attach to other wires using a burn-in adapter. I use mostly Oyaide plugs and IECs for the DIY LoRad cables.
I am near the end of a long audio journey. After 6 years of upgrades and changes my system is finally sounding great. But, being an inveterate tinkerer, I wanted to hear the difference between an Oyaide M1 and an Oyaide P-079 upstream. The other day I substituted an F1 IEC for a C-004 IEC and the former was a big improvement. What would switching the M1 and the P-079 do to the sound? Which one would sound better upstream? I was curious. Before making the switch the P-079 was upstream. I figured there was an even chance the M1 would improve the sound. After all, it is the top of the Oyaide line, and deservedly so. I have three M1s and 3 F1s in my system.
How important is location with these little Oyaide miracle makers? Well, if you think you know about your audio system you should try a similar experiment. The M1 upstream killed the sound. Even with all the high end cables in my system humming the sound became lifeless and thin. The synergy was awful. My system needed the warmth and fullness of the P-079 upstream of the M1 to give it the beautiful sound I had been enjoying before making the change.
The fact that a single plug can change the sound so profoundly -- completely transforming it for the better or the worst in the face of high end components and cables -- is both surprising and humbling. The moral of the story is that you can never do too much tinkering to find the very best sound that your system is capable of producing.
Needless to say, back the M1 and P-79 went to their original places. Have you had an experience with your system where one small step completely made -- or ruined -- the sound?
Disclosure: I have no connection with any audio company except as a customer.
I use PCs, SCs and ICs in series. I have talked about this in other threads and will not restate this here. Some of the patch wiring I use is Supra LoRad that I attach to other wires using a burn-in adapter. I use mostly Oyaide plugs and IECs for the DIY LoRad cables.
I am near the end of a long audio journey. After 6 years of upgrades and changes my system is finally sounding great. But, being an inveterate tinkerer, I wanted to hear the difference between an Oyaide M1 and an Oyaide P-079 upstream. The other day I substituted an F1 IEC for a C-004 IEC and the former was a big improvement. What would switching the M1 and the P-079 do to the sound? Which one would sound better upstream? I was curious. Before making the switch the P-079 was upstream. I figured there was an even chance the M1 would improve the sound. After all, it is the top of the Oyaide line, and deservedly so. I have three M1s and 3 F1s in my system.
How important is location with these little Oyaide miracle makers? Well, if you think you know about your audio system you should try a similar experiment. The M1 upstream killed the sound. Even with all the high end cables in my system humming the sound became lifeless and thin. The synergy was awful. My system needed the warmth and fullness of the P-079 upstream of the M1 to give it the beautiful sound I had been enjoying before making the change.
The fact that a single plug can change the sound so profoundly -- completely transforming it for the better or the worst in the face of high end components and cables -- is both surprising and humbling. The moral of the story is that you can never do too much tinkering to find the very best sound that your system is capable of producing.
Needless to say, back the M1 and P-79 went to their original places. Have you had an experience with your system where one small step completely made -- or ruined -- the sound?
Disclosure: I have no connection with any audio company except as a customer.
- ...
- 22 posts total
- 22 posts total