I of course was talking only about situations when there are no differentially balanced circuits. But even then I would listen given the opportunity. So far I discovered only one thing that you cannot really do by ear, you can try though, and that is aligning the cartridge. I also wouldn't set tracking force by ear because what I may like most might damage the cartridge. So, Tanya, listen as much as you can, some results might be surprising. Trust your ears. And one more thing, unless you already know it. If you buy new or lightly used cables, make sure to let them play for at least couple of hundred hours before judging their performance, pay no attention to how they change within this time interval unless you want to entertain yourself. Some cables require 300 hours of breaking in and power cords often even more.
Single ended vs xlr balanced
I have switched backwards and forwards (going slightly mad in the process) testing (long run) interconnects.
I know some sound engineers, and they tell me I am probably persuading myself that balanced is better than single ended and THERE IS NO REASON WHY SINGLE ENDED CAN SOUND INFERIOR TO BALANCED. Sorry to use capitals but this seem to be a fair summary of the be all and end all of technical discussion. If I was to guess however, my mind would tend to follow the technical opinion not go against it, surely? In my mind the balanced is a deeper more airy sound, just better presence all round. The technical response is that I am not comparing like with like, as the balanced runs at higher voltages and subsequently higher volume (6db). I had a shock at this news and found out therefore by accident that my Bryston 28bsst2s amps have a switch upping the output from 23 to 29db to compensate. Also did I hear properly that Bryston kit is set up preferring balanced? My processor is a Bryston sp3 so maybe my preferred balanced system is what I needed anyway. But it is odd that a reputable company like Bryston would have such a policy (if it has foundation) and not stress that on their literature. If my system can be adjusted for speaker levels then volume output is irrelevant - or is it if that higher voltage has some effect?
And don't get me started on aes/ebu vs spdif! The aes to me is noticeably superior for the same reasons as the rca vs xlr debate. Then hdmi vs spdif ... (Time for my medicine ........)
So my question is - forgetting technicalities which can get more and more complicated by the minute - do other peoples' ears agree with mine?
I know some sound engineers, and they tell me I am probably persuading myself that balanced is better than single ended and THERE IS NO REASON WHY SINGLE ENDED CAN SOUND INFERIOR TO BALANCED. Sorry to use capitals but this seem to be a fair summary of the be all and end all of technical discussion. If I was to guess however, my mind would tend to follow the technical opinion not go against it, surely? In my mind the balanced is a deeper more airy sound, just better presence all round. The technical response is that I am not comparing like with like, as the balanced runs at higher voltages and subsequently higher volume (6db). I had a shock at this news and found out therefore by accident that my Bryston 28bsst2s amps have a switch upping the output from 23 to 29db to compensate. Also did I hear properly that Bryston kit is set up preferring balanced? My processor is a Bryston sp3 so maybe my preferred balanced system is what I needed anyway. But it is odd that a reputable company like Bryston would have such a policy (if it has foundation) and not stress that on their literature. If my system can be adjusted for speaker levels then volume output is irrelevant - or is it if that higher voltage has some effect?
And don't get me started on aes/ebu vs spdif! The aes to me is noticeably superior for the same reasons as the rca vs xlr debate. Then hdmi vs spdif ... (Time for my medicine ........)
So my question is - forgetting technicalities which can get more and more complicated by the minute - do other peoples' ears agree with mine?
- ...
- 45 posts total
Just because you have XLR inputs and out puts does not mean your system is truly balanced. A lot of equipment will take a balanced signal and convert it to single and then (some) back out to the Xlr out put. I have found that system that are balanced all way through sound better with XLR cables enjoy Pete |
This is something to test your rig. I suspect, Kharkov never heard anything like that in either balanced or unbalanced configuration. https://www.youtube.com/watch?v=bBGI22_lp6U |
I own an amp that is not truly balanced, but does have both XLR and single ended inputs. The manufacturer recommends the XLR inputs. After listening to both using 1m length cables, it was obvious the balanced inputs sounded better by a wide margin. Better dynamics, more lively, more punch - all of which was lost when using the single ended interconnects. Is it possible for cable type to make that much difference when the length is only 1 meter? I suspect it has a lot more to do with the amp specs for the 2 input types. The input impedance/sensitivity of the unbalanced input is 12k Ohms/1.9 volt. Input impedance/sensitivity of the balanced input is 100k Ohms/3.8 volt. My guess would be that system matching between my pre and amp is better when using the balanced inputs because of the input impedance. |
- 45 posts total