VPI Classic hum

Bifwynne - I have a Classic 1, it's about a year old; upgrading the armtube to steel was an option I paid extra for. There's no compatibility issue with the Maestro that I can make out so far, but that hum is still there! As Macdadtexas said, it's the design quirk ... odd that I initially never noticed it a year ago ... getting a Soundsmith is going to be another expensive trial.

Need to reassess things the next few months ...

Bassraptor, very curious, very curious indeed. As mentioned above, I installed a Maestro Wood cartridge on my Classic 1 with stock arm. I may be hyper critical here, but I think I detect a bass resonance or ringing in the 50+ to 100+ Hz registers. I surmise this because I still detect the bass bump when I turn off my sub, which rolls off at 40+ Hz.

As also mentioned, I've been trading e mails with Mike at VPI about the issue. I infer from his messages that he may have been able to replicate the bass bump at the factory. He suggested that I exchange out my stock aluminum/stainless steel arm for an all stainless steel arm. Mike explained that the stainless steel arm has a higher damping factor and effective mass. My questions back to Mike were (i) a request that he confirm whether in fact he was able to replicate the bass bump using the stock arm and (ii) if yes, whether the stainless steel arm corrected the problem. If the answers to the foregoing questions are "No," I may have to rethink what to do next.

Oh BTW, I believe the bass bump relates to the phono stage because I do not detect the bass bump when using my CDP.

Perhaps you can help me with my issue by telling me how you set up your cartridge. In particular, (1) did you use the VPI jig to set alignment and overhang? (2) At what mass did did you set VTF? (3) How did you set VTA/SRA -- with the back end of the cartridge above or below a straight horitontal plane for the cartridge? (4) Did you use a head shell weight? (5) Did you use the VPI mat, rubber damping ring and clamp. (6) Finally, I assume azimuth was true.

Now, as regards your problem, maybe my ears are just plain shot after obsessing endlessly over my perceived bass bump, but I do NOT detect any humming coming off the phono stage -- just a little tube hissing, which is normal. My rig is an ARC PH-7 phono pre, an ARC Ref 3 line stage and an ARC VS-115 amp. I have not as yet hooked up a ground wire from the Classic to the PH-7. The I/C from the PH-7 to the Ref 3 is nothing fancy, just a set of better grade off the shelf Auvio brand RCA jacks I bought at Radio Shack. The I/Cs from the Ref 3 to the VS-115 are balanced Kimber Heros.

It seems to me that we have similar TT set ups. Logic dictates that if we conform our set ups as much as possible, perhaps we can help each other sort through our respective TT issues. I gather you have suffered through I/C problems, grounding and proximity of the I/C cables to inductive current lines. If so, the only thing remaining is that your Maestro may be defective or, perhaps more likely, the stainless steel arm in some way is creating an induced electro-magnetic field because of proximity to the motor. Remember, my stock arm is a combo of aluminum/stainless steel.

Last thoughts, did you mention above whether you think the hum is at 60 Hz? If so, that would be a strong pointer to the motor and stainless steel arm. Have you contacted Mike at VPI, either via e mail or phone?

Sorry for the long post. Just trying to help.

Please write back with your thoughts. Thanks.

Bassraptor, I had a another thought that might help to localize the cause of your hum problem. You said you get the hum when you place the stylus on the record surface, mostly in the first couple of tracks. I'm not trying to be simple here, but do you get the hum with the stylus sitting on the record, but with the motor turned off? I suspect that the answer is no. Then if you start the motor, I assume that the hum starts up. If I'm on target so far, what happens if you touch the ground wire to the tone arm base. Does the hum go away? If not, what is your ground wire connected to. If the pre, any possibility of a ground loop? Just for fun, if you can extend the ground wire touch a water or gas pipe, you might get a clean and solid ground that will eliminate the hum.

I have a vested interest in your results. Mike at VPI just advised me that with the Maestro installed, the "Classic 1 arm . . . resonance was at 16HZ, way to[o] high. It will be at 10 HZ in the Classic 3 arm." As is mentioned above, the Classic 3 arm is all stainless steel. Hence, if I upgrade to the Classic 3 arm, I may resolve my bass resonance problem, but substitute a new hum problem.

Please let me know how you make out. Good luck!

Bifwynne - Thanks much for your input and suggestions. Give me 2-3 days to detail my history with the Classic since I got it last year. And also to try out some of your suggestions and my own procedures.

My Classic with steel tonearm tube sounds great with the Maestro.

Man, with the Clearadio and Rega I've owned, I never had to take this much trouble!
cheers

I hear ya! My goodness, I NEVER had anywhere this much grief with my old Thorens. I think the Classic is querky because of the uni-pivot arm. Everytime you mess with VTF, you screw up up azimuth. VTA is just trial and error, but at least we can adjust it with the star wheel. I believe that VTA in the Rega arm is a pain to adjust -- at least in the RB 301 I used to own.

As I wrap up my business with Mike at VPI, I will suggest that the company figure out a better way to adjust the arm without all the grief.

I hope it's all worth the effort when we're done.

Please let us know how you make out. I'll post something once I set up the Classic 3 arm.

Cheers to you.