What Class D amps will drive a 2 ohm load

Just asking.

I see specs into 4 ohms but nothing into difficult speaker loads (like Thiel CS5's).

Thanks for listening,

Dsper

dsper08-25-2019 12:17am

...
420 posts total
View entire discussion

georgehifi Details Discussions Posts This discussion 10,312 posts 11-26-2019 at 10:48pm Copy Comment URL Report Comment Edit Delete dsper Back to the OP’s question What Class D amps will drive a 2 ohm load into his Thiel CS5’s The proof is in the two posts done here, about Class-D and it’s ability to perform/drive "optimally" into hard loads full range, (not just to be stable!!) even with one of those speakers being very efficient at over 90db!!! joysjane https://forum.audiogon.com/discussions/what-class-d-amps-will-drive-a-2-ohm-load/post?postid=1838669... golfnutz https://forum.audiogon.com/discussions/what-class-d-amps-will-drive-a-2-ohm-load/post?postid=1838728... When are the Class-D spruikers going to stop trying to push them like they’re the total answer to amplification, and sell them for what they are, good for easy/medium loads and not hi-end "yet", like Agostino, Gryphon, Solution, Boulder ect ect for driving the types of speaker discussed here, and the topic of this thread!!!!!!! Cheers George
nitrobob Details Discussions Posts This discussion Message User 261 posts 11-27-2019 at 02:04am Copy Comment URL Report Comment Edit Delete You guys have me thinking. I’m not at all on your level of knowledge. So now is a good time for me to throw this out there. I have Legacy Focus mains, with Legacy Marquis center and a nice pair of Ascend Acoustics Sierra 2 raal surrounds. Couple of 18 inch subs also. We do up some video concerts while entertaining, classic rock mainly, and volumes stray up over 110 db ( at 10 feet ). The sound in that room is phenomenal. I had a new ATI Signature 6005 series amp, and occasionally the right channel would just quit. I called ATI. They were really nice about it and explained that probably the Legacy’s were dropping below 2 ohms and tripping the channel. ATI then called Legacy and found out that they indeed did go down to 3 during certain conditions. ATI replaced the board with one that could take more punishment, no questions ask. Here’s my question. Legacy has just released their "V" series amps. They are D series with Ice technology. It's double the output of my ATI. 600 verses 300 per channel . It sounds like a perfect fit to me. Any drawbacks ? Please don’t scold me on the effects of loud listening. I’m 64, been racing cars and enjoying loud hobbies my entire life. Too late to cradle myself now .. Thanks for any input.
georgehifi Details Discussions Posts This discussion 10,312 posts 11-27-2019 at 03:01am Copy Comment URL Report Comment Edit Delete nitrobob I have Legacy Focus mains Very nice speakers but sorry a b***h to drive, neither your amp (mosfet) or a class-D will suffice, they’re just not up to getting the very best out of these Legacy’s That’s a pretty nasty looking impedance and -phase angle graph. Read back at amps I have suggested and you get the idea of what you need. Doesn’t have to be high wattage 50-100w will do, as those speakers are 95db, BUT!! you need gobs of current all the way down to 2ohms, look at what I say about "almost doubling wattage" for each halving of impedance, then go and search for amps that come close to doing this. https://www.stereophile.com/images/archivesart/LEG20FIG1.jpg (fig.1) reveals that it needs to be used with an amplifier that can deliver high current into low impedances. Not only are there two minima in the bass of less than 2 ohms, and another of less than 3 ohms in the mid-treble, but there is an amplifier-crushing combination of 3.3 ohms magnitude and 60 degrees capacitive phase angle at 20Hz Cheers George
golfnutz Details Discussions Posts This discussion Message User 231 posts 11-27-2019 at 03:56am Copy Comment URL Report Comment Edit Delete @nitrobob - it would appear that V series amp is based on the IcePower 1200AS1/2 modules (not sure if it’s the 1, 2, or combination of both), which has a minimum impedance of 2.7 ohms. They also mention you should use a 20amp circuit for best results. You might want to consider using a high current stereo amplifier for left and right channels only, and something different for the center, and surrounds.
nitrobob Details Discussions Posts This discussion Message User 261 posts 11-27-2019 at 12:54pm Copy Comment URL Report Comment Edit Delete Thanks guys. My current ATI 6005 uses two 20 amp circuits as I had to run a dedicated line for my second output.

420 posts total
View entire discussion

More to discover