Here is a easy to do interconnect that will sound like it cost $300. Use Belden 89259 DIY RCA Interconnect Cables This is an unbalanced RCA interconnect cable design using the low capacitance Belden 89259 coaxial cable. Belden 89259 is a RG-59/U plenum rated coax cable with a stranded (7x30) center conductor and bare copper braid shield. Insulating materials are FEP (Teflon) dielectric and outer jacket. The heavy copper shield, low capacitance and premium insulating materials make this a super cable for a wide range of DIY audio cable projects, it works great for speaker cable, interconnect and digital cables.
Required Parts and Tools
The following parts will be required to complete a stereo pair of the interconnect RCA cables.
Description Quantity for one pair
Belden 89295 Coax Cable
Male RCA Plugs
1/4" TechFlex (expandable sleeving)
1/2" Heatshrink
Solder 2 (equal finished lengths)
4
2 (1 inch shorter than coax cable length)
4 (2.5 inches each)
As required.
Belden 89259 RCA Cable Construction
The following steps outline preparation of the Belden 89259 cable:
1. Using a stripper/cutter, side cutters or a utility knife, cut 2 equal lengths of Belden 89259 cable.
2. Measure the approximate stripping length of cable against the barrel of the RCA plug
3. Using a sharp utility knife, lightly cut the cable jacket along the measured stripping length
4. Pull back the cut jacket and trim away the excess
5. Comb back the copper shield and tightly twist together
6. Strip away approximately 3/16" (5 mm) of insulation with a coaxial stripper
Note: When using a coaxial stripper to remove the insulation, turn one revolution only. Any more than one revolution may cut into the conductor. You can practice using the coaxial stripper on a test piece of coax cable before using it on the Belden 89259 cable. A stripper/cutter may be used instead of a coaxial stripper.
The instruction below have been put together for a Cardas Silver RCA plug. Of course you can use your favorite style of plug, but depending on the RCA plug that you choose, the specific details will change slightly, but the general idea is the same.
Photograph 5: Male RCA Plug
7. Bend the bridge so it will accept the twisted shield by placing a screw driver on mid-point of Bridge
8. While holding the screw driver in place, carefully tap the screw driver to bend Bridge
Note: Do not over bend the bridge. Doing so will cause interference with the coax insulation. The center of the bridge may crack while bending. This is normal as a result of the brittle material.
9. Bend the bridge until the gap is just large enough to fit the twisted shield
10. Preheat and apply solder sparingly to both the conductor and tit
11. Solder the twisted shield to the RCA bridge using the same method described in step 10.
Note: Before connecting the remaining RCA plug on the other end, you must first insert the TechFlex expandable sleeving and heatshrink wrappings.
12. Slide the TechFlex expandable sleeving and the two 1/2" diameter x 2.5" long heatshrink wrappings over the cable from the non-terminated end.
13. Repeat soldering steps 10 and 11 to terminate the remaining cable end.
14. Using a the continuity or resistance measurement feature on a multimeter, test for cable shorts by placing one lead on the RCA signal pin at one end and the other lead on the RCA barrel or cover (
Note: An infinite reading or no value indicates that the cable connection is good and not shorted.
15. Screw on the RCA covers an place heatshrink about 1/2" over the RCA plug and shrink the entire length.
Or just buy a pair
--------------------------------------------------------------------------------
Required Parts and Tools
The following parts will be required to complete a stereo pair of the interconnect RCA cables.
Description Quantity for one pair
Belden 89295 Coax Cable
Male RCA Plugs
1/4" TechFlex (expandable sleeving)
1/2" Heatshrink
Solder 2 (equal finished lengths)
4
2 (1 inch shorter than coax cable length)
4 (2.5 inches each)
As required.
Belden 89259 RCA Cable Construction
The following steps outline preparation of the Belden 89259 cable:
1. Using a stripper/cutter, side cutters or a utility knife, cut 2 equal lengths of Belden 89259 cable.
2. Measure the approximate stripping length of cable against the barrel of the RCA plug
3. Using a sharp utility knife, lightly cut the cable jacket along the measured stripping length
4. Pull back the cut jacket and trim away the excess
5. Comb back the copper shield and tightly twist together
6. Strip away approximately 3/16" (5 mm) of insulation with a coaxial stripper
Note: When using a coaxial stripper to remove the insulation, turn one revolution only. Any more than one revolution may cut into the conductor. You can practice using the coaxial stripper on a test piece of coax cable before using it on the Belden 89259 cable. A stripper/cutter may be used instead of a coaxial stripper.
The instruction below have been put together for a Cardas Silver RCA plug. Of course you can use your favorite style of plug, but depending on the RCA plug that you choose, the specific details will change slightly, but the general idea is the same.
Photograph 5: Male RCA Plug
7. Bend the bridge so it will accept the twisted shield by placing a screw driver on mid-point of Bridge
8. While holding the screw driver in place, carefully tap the screw driver to bend Bridge
Note: Do not over bend the bridge. Doing so will cause interference with the coax insulation. The center of the bridge may crack while bending. This is normal as a result of the brittle material.
9. Bend the bridge until the gap is just large enough to fit the twisted shield
10. Preheat and apply solder sparingly to both the conductor and tit
11. Solder the twisted shield to the RCA bridge using the same method described in step 10.
Note: Before connecting the remaining RCA plug on the other end, you must first insert the TechFlex expandable sleeving and heatshrink wrappings.
12. Slide the TechFlex expandable sleeving and the two 1/2" diameter x 2.5" long heatshrink wrappings over the cable from the non-terminated end.
13. Repeat soldering steps 10 and 11 to terminate the remaining cable end.
14. Using a the continuity or resistance measurement feature on a multimeter, test for cable shorts by placing one lead on the RCA signal pin at one end and the other lead on the RCA barrel or cover (
Note: An infinite reading or no value indicates that the cable connection is good and not shorted.
15. Screw on the RCA covers an place heatshrink about 1/2" over the RCA plug and shrink the entire length.
Or just buy a pair
--------------------------------------------------------------------------------