Ascend Acoustics Sierra 2 vs. Dynaudio Focus 140/160


I am putting together a new system which will consist of an Audio Research SP14, McCormack DNA-1 Deluxe, and a new set of smaller speakers, which I will look for on the used market. The McCormack is on its way and I’m currently looking for a good SP14 and speakers. The plan is to use these speakers in a smallish space while I take care of my elderly and ill Father. I will eventually relegate these ‘new’ smaller speakers to a bedroom system and get larger towers for the new system. I do have a set of Klipsch Heresy IIIs, and a much older set of Klipsch Cornwalls, which I may try out before opting for a new(er) set of towers.

I understand that the Ascend Acoustics Sierra 2 is a fantastic option and is an extremely detailed and musical speaker, and I’m confident I’d be very happy with them. Other than the RAAL tweeter, the Dynaudio Focus 140, or possibly a 160 is very similar in that regard. The Dynaudio has an impedance of 4Ω, while the Sierra 2 is 8Ω. The McCormack DNA-1 Deluxe does 330 at 4Ω, so I will need to be mindful not to crank the volume, but I am unlikely to do so. Luckily, the SP14 has an attenuation knob, which will certainly help in this regard.

I should mention that I have not listened to either speaker as I do not have an option to do so, but I have read numerous reviews and both seem to be stellar options.  I also have never listened to a ribbon tweeter.

Budget is $1.2K, or thereabouts, but I certainly wouldn’t be adverse to saving some money since I’m spending ~ $3K on the SP14 and the McCormack DNA-1 Deluxe.

I have wanted both of these speakers for quite some time. I am leaning just a bit towards the Sierra 2. My quandary is that I have found what I believe to be a pretty danged good deal on the Dynaudio Focus 140. Sierra 2s are somewhat difficult to find and will likely cost around $4-500.00 more than this deal I found on the Focus 140s.

I also considered the Revel M22, but again, they are difficult to find, more expensive than the pair of Focus 140s I found and the reviews aren’t quite as good. Any other speakers I should be considering? Also, I am not in any particular hurry, but that deal on the Focus 140s won’t last for too long.

At any rate, I’d be happy to read your comments on these options as well as any other suggestions you may have. The one non-negotiable requirement is that I am not interested in any speakers manufactured in china.

Thank you.

 

1911

As far as the input board flaw is concerned, I believe that only affected early input boards and that the DNA-1 Deluxe is not so afflicted. I will contact SmC or McCormack of VA to find out for sure next week.

Uh, no.  As far as I know the Deluxe version used the same input board as the original and there’s no distinction.  I hope ur right, but I highly doubt it.  Contact SMcAudio if you will, but the news is not good especially for the DNA-1.  Like I said, just leave the DNA-1 on 24/7 and ride it for as long as u can. Best of luck. 

@soix: If you are correct and my DNA-1 Deluxe is afflicted, then I will sell it. I don’t particularly relish the very real possibility of a fatal flaw hanging over me. Unfortunate that I was not aware of this flaw on the Deluxe prior to my purchase, which was last week. I did a fair amount of research on the McCormack and I found no mention of this flaw. Neither did anyone mention the flaw during several forum discussions. This is a severe disappointment; however, I am glad you brought it to my attention.

Perhaps an Odyssey Khartago, Classé Fifteen, or an Audio Research D240 MK II would be a more reliable choice.

Sorry man. Don’t mean to be a buzzkill and you may get many years out of the amp as it’s pretty hit or miss. My guess, use it til it dies if it does, then sink another $2800 into it with Steve’s latest upgrades and you’ll have a new SOTA amp on the relative cheap. Just my $0.02 FWIW.

@soix: I just had a fairly long conversation with Pat at SMc Audio. Great news! He viewed photos of my McCormack DNA-1 Deluxe and it appears that my unit has already had this issue addressed with a new R1 Drive Board. He told me that with that board, I won’t have to worry about any degradation that would lead to failure. He still wants me to take the cover off to confirm, but it looks like I lucked out. Thanks for the information as I never would have known this unless I spoke to Pat at SMc. I’m sure you can imagine that I feel a lot better now.