CAT SL-1 Ultim. Mk2 vs Manley Steel. for CAT JL-2

What cartridge are you using? I would recommend a Placette Active Preamp & the ASR Basis phono stage. The Placette Active will outdo anything until you go above 10K. As for phono stage the ASR is on special here (demo) and is able to accomodate multiple cartridges. Otherwise there is a following on Supratek here. I haven't heard it but it seems to be a great compromise. Whatever you do I am sure the sound will be great. I have the 7s w. VTL & a custom phono stage due any day now. (6 months to make, but lets see how it sounds). I was using a Groove w. my Placette before. The Groove is excellent in most areas but just misses in a few areas & can't easily be tailored to different cartridges. Hence I sold it.

Ubglub, Jafox has the JL3 Signatures ($30k/pr) which are rated at 150 watts each. The JL3 (standard) monoblocks, also rated at 150 watts each, are $22k/pr, and the JL3HCs are basically the same thing, set up for high current capability. The JL3 Signatures are the all out version, including larger, more refined output transformers than the standard JL3s. You are correct, there is no CAT website presently.
Brian

Ubglub: I have no knowledge of the JL-3hc even though this site lists it as a CAT product model. Perhaps this is the JL-3 Non-Signature that Brian at EssentialAudio has mentioned a few times here. But at $10k, I have to believe that would be per amp for a $20k total price; this sounds mighty close to the $22k Brian talked about for the JL-3 non-sig. Or perhaps, this is a totally different or even a non-existant model. Brian and his CAT dealer friend in Chicago know much more about the CAT product line than I do. Ideally, calling Ken Stevens would make the most sense for you to get all your questions answered. He is very helpful.

Concerning power output, the JL-2 stereo amp like the JL-1 monos, uses 8 6550 tubes for each channel to get a CAT spec'd 100w output. The JL-3 Sig uses 16 6550 tubes for each channel to achieve a spec'd 150w.....not 200w. I suspect the actual power output is higher for all these models. But the 300w Class A rating for the JL-3hc model sounds a bit fishy to me unless it is actually configured in a non-triode topology.

The CAT amps are known for some serious current output and can drive some mighty difficult real-world speaker loads out there. When I had Magnepan 3.5 speakers and the Audio Research Classic 150 mono amps, which were rated at 150 Class A, these amps shut down regularly when really "asked" to deliver to these speakers; they simply could not deliver as expected. The Wolcott P220 monos at a rated 220w output had no problem driving these speakers at all. And just before I sold the Magnepans, I used the JL-3 Sigs and again there was no problem at all. Specified power rating between models is often not apples to apples - 150 watts did not equal 150 watts between the ARC and the CAT.

John

Incredible timing - I see that while I was typing my response, Brian replied here. Ah, the psychic powers within us. 8-)

Dgad,
I will be using Benz Micro Ebony LP mc cart or Koetsu Jade Platinum mc cartridge.I prefer Jade Platinum more because it is more lush and more rich in texture but have good speed,dinamics and transparency. If I can not get pure neutrality from my sistem(which I suppose never will...) then I am more for warm side instead of analitical!
I heard about Placette pre but for ASR Basis phono it would be the best to drive it via balanced input(TAS recomm.) or? And I need one Transp. Audio Reference MM interconnect more in this case!

Jtinn, yes I will use only Kuzma's turntable with his Airline tone arm,because he lives 90km from my house. It is good to have someone who build turntables so close if something happened.Have you heard Kuzma Stabi Refer. with Airline tonarm, yet? Whit which cartridge?