DIY speakers vertical array a la "pipedreams" syst


Have any of you worked on a multi drivers vertical array type of speakers ...something that would look like a diminutive version of the http://www.nearfieldacoustics.com/The%20System.htm systems ?

What were the results?

i have a suddent interest in knowing why so many people
prefer this kind of setup to systems of equivalent quality drivers/enclosures with less in number ...

Anyone has a good ressource for buying excellent drivers
( only the drviers ) and or reviews of such ?

i will need a 15-18" driver for my sub neway , even
if i still go with ESLs ..

But the vertical array systems attract me for a single reason, build is easy and it should cost equivalent to electrostatics ( since no need for $$$$ step up transformer
but multi drivers need to be purchased ..

I would be considering a desing of a few feet tall with a
front face of 12" to 18" maybe with an opened rear for dipole action since they can't reach the front in their resonnat frequency ...mmmm

could be something in the 3 feet tall in total
wonder how many driver i could place on that :p

what do you guys think?

then also, about the need to drive all the drivers,
will it ask for a really powerfull amplification ?
or since all the drivers are working less powerfull to
attain the equivalent sound pressure, they thus require less power ?

what do you think of nerafield acoustic theory that
having more drivers permits the drivers to be worked at lower power and drivers are more accurate at lower power?

thanks for your time,

anything will help :)
jinmtvt
Can anyone help me figure out how to send Fred an email at that page, I don't see the link. Thanks
http://www.geocities.com/dmitrynizh/labaffles.htm
This page has a lot of great info on open baffle and line array theory as does the Linkwitz page for anyone else interested in these designs. I think it would be a great project that hopefully would achieve great imaging similar to planars, but with the bonus of higher sensitivity and dynamics.
I'm not aware of any open back line array plans. I had tried to build a pair using ten Parts Express 4.5" Vifa "buyout" woofers with a single tweeter and they sounded terrible, but that's probably a product of my design incompetence rather than a generic problem with open back arrays. If you're interested in arrays you should read Jim Griffin's white paper on that topic at http://www.audiodiycentral.com/resource/pdf/nflawp.pdf

After building three nearfield line arrays I'm convinced they are superior to point source speakers in several regards that are discussed in Dr Griffin's paper, but there are two offsetting disadvantages: 1) If you use quality drivers they are expensive, and 2) The enclosures are a much bigger project than smaller two or three way speakers. The driver quality thing is obvious - sixteen $100 woofers and 16 $118 ribbon tweeters are more expensive than two of each:) The enclosure construction issue becomes obvious when you have to lift a 4X8 sheet of 1" mdf on to the table saw roller tables and guide it accurately throught the saw. But when you have finished the project and listen to the completed speakers you will know it's worth the extra effort and expense.

Regarding the cost, I divide line arrays into three categories: 1) The obscenely expensive mainstream products like the Pipedreams and the Epiphanies. 2) The non-mainstream high end products offered by Selah Audio and GR Research, and 3) The DIY projects that use budget drivers.

If you have the money definitely choose alternative #2. I have heard Rick and Danny's arrays. They sound really good and even as completed ready-to-play speakers sell for less than half the price of the mainstream products. If you don't have $2,500 or more for a DIY enclosure kit, you are limited to alternative 3.

I'm aware of several budget DIY line array projects. Probably the best is the Linus I, which is no longer offered, but Jim Griffin will email you a copy of the plans for the asking. The Linus I uses twelve 5" MCM aluminum cone woofers (the shielded version of the driver that was used in the Bottlehead Straight 8) and six Silver Flute planar tweeters per side. The parts for this project will cost about $600, most of it for the twelve tweeters.

To get below the $600 cost you need to use a single tweeter instead of a planar array. I did this with the Fredarrays. It's not the best choice, but the single tweeter mated with the woofer array better than you would expect. Several people who heard the FredArrays at the Great Plains Audio Fest were impressed, one so much that he later bought them from me. I plan to build another pair soon. This time I will use the same Silver Flute woofers which, at $12.50 each by the case, are an incredible bargain and sound better than the $25 Vifa TC-series woofers they compete with. I want this one to be more SET friendly and plan to use eight per side to get a 16 ohm impedance. I also plan to use a better quality tweeter than the $12 MCM titanium dome in the original FredArray. possibly an Eminence compression horn.

The next step down the ladder would be to with for Parts Express to come up with another Vifa 4.5" buyout offer. These ususall go for $5-7 and sould pretty good. There's a good example of an array using these at
http://www.lonesaguaro.com/speakers/array/array.htm

The next step down from there would be an array using dirt cheap parts like these 79 cent Parts Express "factory buyout" tweeters at http://www.partsexpress.com/pe/showdetl.cfm?&DID=7&Partnumber=279-010

I have some doubts about this extreme budget level. These tweeters have to sound terrible, like the tweeters in that Honda with a fart box subwoofer and cheap tweeters that pulls up next to you at the light with the windows open and rap music going full blast, and an array of 20 will sound like 20 spittng tweeters instead of one. Just my two cents.
Thanks Fred for all the info and advice! I've been scouring the diy forums and pages like yours trying to absorb as much as I can, kind of daunting sometimes. My goal is to be able to use a pair of Bottlehead amps or similar SET to drive whatever I build. I'm wondering if I shouldn't just try a full range driver on an open baffle with bass handled by a sub, like the Bastanis, to get my feet wet before trying to tackle a line array. Any thoughts? Nice work by the way on your page and all your speakers.
The full range driver is a viable option, but I'm skeptical about getting one to sound good with an open baffle. Fostex drivers and the like have so little X-max (0.6mm for the FE-167) that they can easily be driven to excess distortion levels without the control of a good enclosure. Even with a bass reflex enclosure you're going to hear distortion at fairly modest volume levels.

If you decide to use a Fostex here's a link to Bob Brines' web page. I heard his FT-1600 speakers at the Great Plains Audio Fest and was very impressed - they seemed to solve the bass problems I have heard with Fostex and Lowther drivers. He will sell just the plans, a flat pack kit, unfinished mdf enclosures or completed veneered speakers. The enclosures are not complicated and should be easy to build from the $25 plans http://geocities.com/rbrines1/

Another option I highly recommend is Wayne Parham's two way Pi speakers. I just completed a pair of 3 Pi Theater models which I really like, and at 98dB efficiency they sound really good with Paramours. If their $240 ea price is over your budget consider the 95dB sensitivity Two Pi towers at $80 each for the driver and crossover kit. I heard this one too at GPAF and it's amazingly good for the price. All these speakers have bass response that would shame any single driver speaker. http://www.pispeakers.com/