Eminent Technology ET-2 Tonearm Owners



Where are you? What mods have you done ?

I have been using these ET2's for over 9 years now.
I am still figuring them out and learning from them. They can be modified in so many ways. Bruce Thigpen laid down the GENIUS behind this tonearm over 20 years ago. Some of you have owned them for over 20 years !

Tell us your secrets.

New owners – what questions do you have ?

We may even be able to coax Bruce to post here. :^)

There are so many modifications that can be done.

Dressing of the wire with this arm is critical to get optimum sonics along with proper counterweight setup.

Let me start it off.

Please tell us what you have found to be the best wire for the ET-2 tonearm ? One that is pliable/doesn’t crink or curl. Whats the best way of dressing it so it doesn’t impact the arm. Through the spindle - Over the manifold - Below manifold ? What have you come up with ?
128x128ct0517
BTW it's Mike Kiser.  Just jumping in to say that I've posted some turntable and tonearm pictures in my virtual forum.  Amp and speakers are in a state of flux, so for now it's just turntable pictures.  As long as I'm here I just want to thank you guys for your insights over all the years.  I haven't solicited much advice directly but have followed a lot of the threads with interest.  Probably the thing I've learned most from this forum is the importance of balance, and the wonderful? world of I beams and leaf springs.  FWIW, I'm going to be sending my manifold, spindle and manifold housing back to Bruce soon.  There is an air flow imbalance that causes the spindle to push in one direction as I increase pressure. It was pushing out. I flipped the manifold and sure enough it started pushing in as I increased pressure.  I contacted Bruce and he told me to send it in for balancing.  I'm not sure I've seen anyone else mention this issue, so just wanted to put it out there. 

I’m going to be sending my manifold, spindle and manifold housing back to Bruce soon. There is an air flow imbalance that causes the spindle to push in one direction as I increase pressure. It was pushing out. I flipped the manifold and sure enough it started pushing in as I increased pressure.


Mike.
This is interesting.
My understanding is that the stock 2.0 smaller lighter spindle needs about 3 psi to levitate. The larger heavier lower resonance stock 2.5 spindle, designed for MC carts, needs in the neighborhood of 5-6 psi to do the same thing. This is for Bruce’ stock builds. Then we get into the custom builds that Bruce has done for clients, like myself. He set my 2.5 up for 19 PSI. In discussions with him at the time it was my understanding that this is the PSI limit for the design.

So based on the above, why are you choosing to increase the PSI ? and does the spindle stays balanced, when it is run at the PSI that Bruce set the manifold up for at his shop ?

Just thinking out loud over coffee this morning.

If I were located far from Bruce in Florida, and the (spindle, manifold) were going to be sent to him for maintenance anyway; I would first be tempted to try rebalancing the manifold on my own. As you are using direct shot wiring set it up without the wiring and just the spindle on (Look Mom, no wires ! - hah hah )

So with just the spindle on, turn on the air at the factory set PSI. Do observations. Now bump up the pressure and observe again. Slide out the manifold itself, and adjust the screws on the one side a bit, on the side it it pushes towards. Open them up a bit equally. What happens ? If it gets worse turn them in again and go to the other side and repeat. Again, just something to try, before it goes back to Bruce.

***********************

lots of turntable tweaks in your Audiogon page.
I really like the way you have set up the thread/floss on your turntable. Interested in the differences you heard compared to the belt setup.

Hi Chris.  I too have a custom 2.5 manifold, set for 12 PSI. I'm sure the fix is to adjust the screws on the manifold to adjust airflow, but there are two issues.  First, I'm not sure exactly which screws should be adjusted, and second, for the most part, I can't get an allen wrench into most of the screws.  The female allen ends are not uniform, they've been buffed down in several places and an allen wrench just can't get purchase.  I've had the manifold out and was only able to turn one screw.  I should have taken a picture. Right now, with a dead level table and 12 PSI, the arm has a very pronounced bias inward (was outward until I flipped it).  I'm dealing with it in the short term by finding a setting that does work, about 5 PSI right now.


  We're getting 6 inches of snow in Greensboro right now, so this is prime listening time, so it will be a while before I send the parts in to Bruce, and there's no way I'm going to try to get it right myself.  That being said, I ain't hating what I'm hearing right now. I know it could be better and not just because of the pressure imbalance. I recently purchased a Soundsmith Zephyr MIMC and was using that for the last 10 days or so. It has a master tape quality, no doubt. Resolution, when setup is dead on, is jaw dropping, but in spite of that, I've gone back to my old reliable Delos for now.  On my rig, the Delos is not quite as resolving, but is noticeably warmer. Add to the mix that two weeks ago I took delivery on a prototype pair of Vaughn Plasma Signature speakers and I'm still familiarizing myself with them. The Delos is sounding pretty sweet through them, even though the speakers are currently being driven by a Marantz SMS-11 power amp. Not ideal, as the speakers are 96db efficient and were designed for low power SET/ Class A  amps. At RMAF they were paired with the top of the line Wavelength amps, and it was something to behold.  Sold me :)  Jim Jordan of Vaughn has shipped me an Almarro A318b tube integrated amp, and when it comes in next week I'll put the Zephyr back in and see if I can get both resolution and warmth with that combination. Someone said an audio system is like baking a cake.  Well I've switched up a lot of ingredients, but I hope I'm homing in on a blue ribbon recipe.

Prior speakers were Audio Artistry Vivaldis FWIW.  They got along famously with the Marantz amp, but in that case there is a very sophisticated  passive crossover between the amp and the drivers. The designer, Sigfried Linkwitz, is on record as saying his speakers are not overly amplifier sensitive. 

While I'm here, a couple more things.  First off, we all know Bruce is great to deal with.  I'd like to add to that list Keith Herron of Herron audio and Jim Jordan of Vaughn speakers. They're both in the same class.  On last thing.  I do a radio show that you can get off the 'net.  It's the World Peace Party on WQFS Guilford College radio, 2-4 PM EST every Monday.  Mostly indie rock and singer-songwriter, and all through 2017 I've featured a tribute to the 50th anniversary of the year 1967 around the 3:00 mark. Hendrix, Love, Moby Grape, The Byrds, 13th Floor Elevators, Cream....  If you're interested, do a search for WQFS and the tunein link should pop up. Content is MP3's and WAV files, mostly played through a laptop with  Dragonfly Red DAC, so it's not exactly audiophile material.
We're getting 6 inches of snow in Greensboro right now, so this is prime listening time

Has the makings for an Audiophile / Music Lover perfect storm.   8^0

For the benefit of the readers these are the set screws that Mike and myself are talking about.

Click on blue text 

ET2 Manifold and Set Screws
 
The Picture is courtesy of a good audio friend. Have not heard from him in a really long time.
If he sees this - Hope all is well !

***************

A shout out for Mike's radio show info.
World Peace Party on WQFS Guilford College radio, 2-4 PM EST every Monday

WQFS

Click on the "tune in" button

***************

Frogman - those Oak leaves are still falling, appear about 40% fallen, and when falling they seem to be attracted to our two storey eavestrough   :^(

Sometimes

I wonder what music Bruce listened/listens to when he sets up a customer tonearm.  

Have never asked him.    

Thanks for the picture of the manifold Chris.  Mine looks nothing like that.  Every screw hole has been, for lack of a better word, buffed.  The edges around the holes have been sanded to where the edge of the screw is merged with the manifold. Not sure why it's that way, but I'm sure Bruce will make it right. 

For now, I've set up two complete armwand / wire looms.  One for the Zephyr and one for the Delos using the carbon fiber and aluminum wands respectively.  My hope is that I can get them both properly calibrated and then be able to swap them out and not have to do a lot of re-alignment beyond SRA/ VTA and tracking weight.  It's not in my virtual system photos, but I do have one of those run-out gauges you can attach to the top of the tonearm manifold housing that allows you to see exactly what the current tonearm height is.