EQ before Preamp?

Joeylawn,

Where you place the Behringer should in some way depend on what your source components are. If all your source components are digital (using digital outputs), then you can place the Behringer before the preamp, and if you have an external DAC, place the DAC between the Behringer and the preamp (or use the Behringer's built in DAC). In this way, you are not putting your digital sources through an A-D conversion. If you place the Behringer between preamp and amp, then all inputs sources will get an A-D, then a D-A conversion in the Behringer, since the unit does it's processing in the digital domain. If you have a mix of analog and digital sources, you might still be better off putting the Behringer before the preamp, since digital sources won't get the extra D-A and A-D conversions since you can run the digital out right into the Behringer. In either placememnt, all analog sources will be put through a A-D and D-A conversion. Keep in mind of course, that if you put the Behringer before the preamp to take advantage of direct digital sources, the Behringer must have enough inputs to handle all your sources.

Eldartford- I use Behringer equipment all the time when doing installs for venues, and gigs for a few bands(the cheapskate ones). I've been in them. Sorry to burst your bubble: I've yet to see one Burr-Brown(DAC/ADC/IC/transistor) Vishay, Caddock, Holco or Ohmite Gold(resistor), Black gate, auriCap, musiCap, V-cap, Solen, RelCap(capacitor), Schottky Diode, toroidal transformer, gold/rhodium plated oxygen-free copper(or even Switchraft) input or output on any of the pieces I've worked with. That goes for 95% of the other professional equipment I've dealt with in the last 30 years as well(except for maybe the Switchcraft parts). These components are found in virtually all of the higher-end audio pieces(I'm not referring to mega-buck units either). The pro manufacturers simply cannot build their gear with high performance parts, and sell it for 200 to $300.00(in the case of the 2496). OH- I forgot: It all sounds the same, right?

Rodman99999...There are bubbles and there are bubbles. Some say rhodium anything is to be avoided, and black gate capacitors aren't anything special. Burr-Brown has no monopoly on good A/D and D/A converters. But, you are entitled to your personal bubble.

Eldartford- Have you ever used any Black Gates in anything? Some say salt, sugar, white flower, beef, MSG, sunlight, etc, etc are to be avoided. Do you? Burr-Brown is recognized in the industry as one of the best. My bubble is one of experimentation and experience with components, in audio equipment over the last 30 years(started by modding new Hafler amp kits for my customers), a love for the sound of live music (as a sound tech and musician), and an extensive(35 year) familiarity with professional equipment. Blah, blah, blah. I'll just enjoy this little bubble, and the Julian Hirschs(I don't ever listen to live music, but I have a pretty good idea what it sounds like") of the world can enjoy theirs. Just think of all the money I coulda saved if everything sounded the same to me too. DARN!!

Umm, Eldartford used to design electronics for nuclear submarines or something like that - he knows his stuff.

Also, I would like to get back on topic here. The Components again are as follows: Linn Kremlin Tuner, Jungson JA1 Preamp, Behringer 2496 EQ, Monster MPA-2250. Those components are 'set in stone' - I just wanna know if there is any MAJOR problems (like overloading circuits - like when you plug a line level device into a phono input-a big no-no). Will, for instance the pre-amp signal 'clip' if I insert the EQ between the preamp and power amp?

***PART 2 - UPDATE - Additional related Question***

For the Subwoofer. The Jungson doesn't have a second line out. My sub is an (Active) Super Nova. The way I plan to hook that up is take a second set of speaker wires from the amp outputs to the speaker-level inputs of the Sub. Is this right?