2. amps-preamps
  3. 1205287253

EQ before Preamp?

I am switching my preamp from a Parasound P3 to a Jungson model that does not have a processor/tape loop like the Parasound does. What will happen when I use this signal path: Linn Kremlin > Behringer 2496 EQ > Jungson Preamp > Power Amp.
joeylawn36111
mordante
511 posts
 
@Eldartford

That is not entirely true I think. Most pro gear is even more expensive then some audiophile brands up to a certain point. A lot of pro gear has to sound good and be able to take a beating. That is why you almost never see real pro's use Beheringer, the build quality is not that good and the sound qulity isn't that good to.
eldartford
4,262 posts
 
Mordante...I am not familiar with the entire line of Behringer equipment, but the DEQ 2496 is built as well as any audiophile gear, and sounds excellent. Any flaws are more than compensated by its ability to correct room effects.

Other pro sound equipment I use includes an Ashly electronic crossover. Circuitwise it resembles my old Marchand and Audio Control crossovers which are audiophile approved, and the construction is far better.

I also have a QSC power amp that I bought only to drive subwoofers. However the darned thing sounds fine full range, and I am using it that way in a second system.

I almost forgot my CarverPro ZR1600 power amps. Driving MG 1.6 speakers, they are every bit as good as the Channel Island D200 monoblocks which replaced them. The ZR1600s are now doing subwoofer duty.
smeyers
181 posts
 
Joeylawn,

Where you place the Behringer should in some way depend on what your source components are. If all your source components are digital (using digital outputs), then you can place the Behringer before the preamp, and if you have an external DAC, place the DAC between the Behringer and the preamp (or use the Behringer's built in DAC). In this way, you are not putting your digital sources through an A-D conversion. If you place the Behringer between preamp and amp, then all inputs sources will get an A-D, then a D-A conversion in the Behringer, since the unit does it's processing in the digital domain. If you have a mix of analog and digital sources, you might still be better off putting the Behringer before the preamp, since digital sources won't get the extra D-A and A-D conversions since you can run the digital out right into the Behringer. In either placememnt, all analog sources will be put through a A-D and D-A conversion. Keep in mind of course, that if you put the Behringer before the preamp to take advantage of direct digital sources, the Behringer must have enough inputs to handle all your sources.
rodman99999
6,206 posts
 
Eldartford- I use Behringer equipment all the time when doing installs for venues, and gigs for a few bands(the cheapskate ones). I've been in them. Sorry to burst your bubble: I've yet to see one Burr-Brown(DAC/ADC/IC/transistor) Vishay, Caddock, Holco or Ohmite Gold(resistor), Black gate, auriCap, musiCap, V-cap, Solen, RelCap(capacitor), Schottky Diode, toroidal transformer, gold/rhodium plated oxygen-free copper(or even Switchraft) input or output on any of the pieces I've worked with. That goes for 95% of the other professional equipment I've dealt with in the last 30 years as well(except for maybe the Switchcraft parts). These components are found in virtually all of the higher-end audio pieces(I'm not referring to mega-buck units either). The pro manufacturers simply cannot build their gear with high performance parts, and sell it for 200 to $300.00(in the case of the 2496). OH- I forgot: It all sounds the same, right?
eldartford
4,262 posts
 
Rodman99999...There are bubbles and there are bubbles. Some say rhodium anything is to be avoided, and black gate capacitors aren't anything special. Burr-Brown has no monopoly on good A/D and D/A converters. But, you are entitled to your personal bubble.
More to discover