If you didn't run the Canare 4S11 in for 400 hours, it isn't a valid comparison. They NEED that much to sound their best. This is from the manufacturer themselves.
Final Report, Canare 4S11 Speaker Cable
I posted this in the original thread yesterday, but it is so buried that unless you were following it, you would never see it. At the end I will add a few more comments.
This is the final report on the Canare 4S11 cables. I let the 25 foot pair break in on my secondary system for almost 19 days 24/7. At the 445 hour mark, I reinserted them into my main system. I first removed the $1500.00 Groneberg Quattro Reference speaker cables and coiled them up under the floor in case I decided to go back to them. After my son helped me install the Canare cables (I had to make larger holes in the floor for the banana plugs to fit) and routing them perfectly, I am happy to say my system now sounds much better. I no longer have the softness in highs I had with the Groneberg cable and the bass is tighter and deeper. I was always under the impression that the higher the price, the better the cable. The fact that a $130.00 pair of speaker cables bested a $1500.00 pair should be a lesson for everyone regarding price VS performance. Now I have the Canare in both of my systems and I am one happy audiophile.
A few more thoughts: The cables sounded good when brand new with a slightly ragged treble and loose bass. I was told it could take up to 500 hours to fully break in. For myself, I did not hear any changes after the 300 hour mark. I let the cables cook longer than planned because I needed help from my son as i had to drill larger holes in the floor to account for the locking banana plugs. My son lives in another state so I had to wait for him. The construction of the terminated cables is as good as many of the more costly brands. I purchased 2 pairs of these cables in 15 foot and 25 foot pairs. My secondary system now has the 15 foot cables back and I am continuing to break them in as I removed them from the system at the 250 hour mark. A lot of people bash McIntosh but my McIntosh MA6600 integrated amp and McIntosh tuner never failed in 19 continuous days of 24/7 service. The heat sinks were never more than slightly warm to the touch.
That’s all folks.
This is the final report on the Canare 4S11 cables. I let the 25 foot pair break in on my secondary system for almost 19 days 24/7. At the 445 hour mark, I reinserted them into my main system. I first removed the $1500.00 Groneberg Quattro Reference speaker cables and coiled them up under the floor in case I decided to go back to them. After my son helped me install the Canare cables (I had to make larger holes in the floor for the banana plugs to fit) and routing them perfectly, I am happy to say my system now sounds much better. I no longer have the softness in highs I had with the Groneberg cable and the bass is tighter and deeper. I was always under the impression that the higher the price, the better the cable. The fact that a $130.00 pair of speaker cables bested a $1500.00 pair should be a lesson for everyone regarding price VS performance. Now I have the Canare in both of my systems and I am one happy audiophile.
A few more thoughts: The cables sounded good when brand new with a slightly ragged treble and loose bass. I was told it could take up to 500 hours to fully break in. For myself, I did not hear any changes after the 300 hour mark. I let the cables cook longer than planned because I needed help from my son as i had to drill larger holes in the floor to account for the locking banana plugs. My son lives in another state so I had to wait for him. The construction of the terminated cables is as good as many of the more costly brands. I purchased 2 pairs of these cables in 15 foot and 25 foot pairs. My secondary system now has the 15 foot cables back and I am continuing to break them in as I removed them from the system at the 250 hour mark. A lot of people bash McIntosh but my McIntosh MA6600 integrated amp and McIntosh tuner never failed in 19 continuous days of 24/7 service. The heat sinks were never more than slightly warm to the touch.
That’s all folks.
- ...
- 29 posts total
Thanks! I'll keep that in mind. I guess I'm not dedicated enough to leave my system on when I'm not listening to it, so it'll take me about 3 or 4 months of use. Since my amps have two pair of speaker outs, maybe I'll hook both pairs up at the same time and see how that sounds. The locking bananas can lock into each other. I've also been burning in a Kimber type wire with a rope in the middle for comparison. I was just wondering if anyone had tried the KnuKonceptz stuff since I don't hear it talked about much? |
I made a nice 7ft pair of these and burned them in on frybaby + (75) hr’s and went on to a more expensive wire just to satisfy my.."cause i can i guess"...well those are run in +/- some hr's....Just for kicks and wanting to finish up running in the canare’s i put them back in...and you know they sound dam nice with my system...a better match and i just cant find a justifiable reason to take them out other than they are not a more expensive cable... lol. I think these are as someone put it "one of the best cable’s period" not just a great budget wire...fwiw. |
@stereo5 thank you for this... with all the ridiculous expensive cable threads creating so much heat and very little light, this is a much needed voice of sanity to be heard yes you need GOOD cables for your system, they are essential for maximize sound quality ... but good does not need to be expensive |
jjss493,221 posts07-27-2021 11:05am Define "expensive". Do you have general guidelines for up to what $ we need to spend on cables? What price level becomes "expensive" and up to what price we are allowed to spend? Please include price limits for all types of cables (speaker, interconnects, power, digital, etc.). Also, please include price limits for all countries, or, if too hard, just for developed, developing, and emerging, country categories. Thank you |
- 29 posts total