2. cables
  3. 1335297906

High Fidelity Cables CT-1designed by Rick Schultz

In December 2011,I wrote that High Fidelity cables led by cable designer Rick Schultz was putting together a new cable.The cable came to market as CT-1.The CT-1 has FINALLY made it into my system!I had obtained a version of the prototype that Rick had been working on.It blew my previous reference Genesis by Virtual Dynamics.I thought I had finally found my end with this cable.This prototype delivered to my ears "Nirvana".Could I be at the end of my quest for the ultimate sound?
No. I received two pairs of CT-1 to replace my prototypes.They went into the system this past Friday.Unable to dedicate time until Sunday listening,I stole a few moments,ducking away from company with anticipation.My guest could tell even with the music set for"ambiance"something was intriguing and I was in for a treat!
The experience:
First off,CT-1 was very user friendly.Installation was simple;the cable is very nice and light.The female RCA fit beautifully unlike any I had found in other cable.It was secure and reliable.It seemed much thought was dedicated to developing a designer fit to an aesthetically stunning RCA connector.Install entailed a few wiggles to ensure what seemed like a compression fit on my RCA.
It was 2-3 hrs. for the 1st step of break in to be complete.At that point I had something different!Today,although they only have 10-12 hrs. on them,I can`t put into words how much my system has transformed.Believe me,I loved my prototypes.However....there is simply no comparision.
The clarity and sound is so natural.
The soundstage is like nothing I ever heard.Resoulution is breathtaking and inner detail is simply hard to believe possible.
The sound has transended and now it simply does not seem as thought I have speakers.
My system is musicians playing music.
I am told with time they will improve and I trust that as it was revealed with the prototypes.I wanted to share my thoughts with you that now.
Unequivocally,a testament to High Fidelity,as the name declares.
High Fidelity Cables for me,the last word on it,after 12 hours!
Truly Amazing

Al
alpass
ddraudt's avatar
ddraudt
609 posts
 
Tbg, Thanks, I love to hear your system. My system is not complete as I am borrowing integrated amp and speakers until mine are built.

I have not tried the still points ultra fives and wonder how they compare with
Finite Element cerabase. (I have at least 30 of those). I will be looking for some SP U5's to try.

For those crazy tweakers out there- I have found ways to damp, isolate and shield wave guides for a better sound (less noise, cleaner, more intimate, dynamic)
using a combination of wood, lead, clay, iso table, iso feet and aluminum foil
They must be off the floor and only wood (and air) touches the wave guides.
I will not have this perfected until I get my new amp and speakers but it sounds considerably better in my current system.
tbg
5,263 posts
 
Audiolabyrinth, I remember long, long ago when two audio friends in NY showed me the impact one of the routing of wires in a line stage and later of the benefits of two or more transformers in an ac filter being at right angles to each other. I guess any current flow has a magnetic field associated with it and that this field when it varies induces current flow within wires near it.

If the ac filter moves, there are induced signals within its circuit. If you can drain this vibration or absorb it by converting to heat, you don't alter the signal.
geoffkait's avatar
geoffkait
23,365 posts
 
vibration isolation is simply the attentuation of structural vibration, including that produced by Earth crust motion, wind, traffic, subways, etc. If it were as easy as coupling then everyone would throw away their 10K dollar isolation stands and the search for gravity waves would be concluded at last. It's the stuff with frequencies below 5 Hz that can have the highest energy and be the most difficult to ameliorate.
ddraudt's avatar
ddraudt
609 posts
 
I know Rick and company have spent years studying vibration control an was involved in a 3 year college project on the subject.
I am just a little fish that have enjoyed removing unwanted "noise" of any kind
from systems for over 3 decades.
Three things... Rick has heard my system and said he liked I have done so far...
Rick Suggested I try using STill Points on the WGPC...
Although Rick has years of experience with this, he is willing to listen to my humble suggestions and, i believe he would use them if he liked the outcome.

I believe resonance control thru herding vibration is great! I like a dash of damping in my system. The iso tables I use dissipate vibration coming from above and below the table (into heat). ALSO, I personally hate the sound of concrete vibration and isolate my system from it.

Anyway... I love to listen and to play with my system so I'm happy!!
Happier than I have ever been now I have High Fidelity products. (plug) ;-)
audiolabyrinth's avatar
audiolabyrinth
4,555 posts
 
@ TBG, Hi, Believe it or not, I already know what you said in your post, I was asking how vibration resonance has anything to do with electrical impedences, thankyou TBg.
More to discover