My Audio Research experience


To all you goners out there, here is my experience with Audio Research.

Approximately four years ago I purchased an AR Reference 75 power amp.  It was on special at the time and I bought if from a dealer in Brisbane, Australia.

I used the amp for the rear channels of my home theatre system which I only use occasionally because I travel a lot for work and I mainly listen to music.

One night I switched the amp on and a white flash and burning smell came from the amplifier and it didn’t power up.  I thought it may have been a tube, and because I had no spares, I reported the problem to my Brisbane dealer and via email to Audio Research.  A copy of the reply sent from AR on the 5th March 2016 follows:

'Thank you for choosing Audio Research and the REF75. I suspect you had an internal tube arc. The internal tube short can also take out a plate or screen resistor. So just replacing the tube will not fix this problem. The resistors also need to be replaced. You can confirm this by checking the bias for this tube. If the bias reads zero, a resistor is open.  This is an easy repair that our distributor in Australia can do.

The SE update for the REF75 comes with a complete new set of tubes including a new set of KT150s.  This is the only way it is sold. If you so choose, Our Australian distributor can also install this SE upgrade for you while the amp is in for repair.'

I then proceeded to order some more tubes to see if a replacement tube would fix the problem.

I ordered the following tubes:

2 x Electro-Harmonix 6H30Pi Gold with Matched Triodes (Balanced)

4 x KT150 Power Vacuum Tube - [Matching (10+ tubes)]

4 x KT120 Power Vacuum Tubes - [Matching (10+ tubes)]

When they arrived, I tried the new tubes but they didn’t fix the problem as the amplifier failed to switch on.  I then contacted my dealer and freighted the amplifier to Brisbane for repair.  This was done in June of last year.  I included all of the above tubes in the package in case they were needed.  I also would have liked the amp to be upgraded to SE status using the tubes supplied if possible.

In September/October last year I enquired about the status of the repair and before Christmas enquired again. After again emailing AR, I was contacted by the Australian Distributor who told me that the service agent in Brisbane had been trying to get parts for the wrong amplifier and that the amplifier would be transported to Melbourne for repair.  I asked them to get me a price for the upgrade using my tubes.

In January/February of this year, I was contacted by the Australian Distributor and had to supply proof of purchase because there was a dispute over whether the amplifier was in fact under warranty when the fault occurred.  I again asked about getting the upgrade using the supplied tubes which were still with the repair agent in Brisbane.  Eventually I was told that I could have the upgrade using AR tubes only, for the heavily discounted price of $3,000 Australian.  Nothing like gouging your customers!!!!!!  Especially when I could have bought a small car for the original cost of the amplifier in Australia.

I chose to just get the original amplifier repaired under warranty which I was told needed a new main circuit board.  This week my amplifier finally arrived back home after nearly 12 months away for a repair under warranty.  The original tubes have been put in a box with ‘Faulty Old Tubes,’ written on the box.  The tubes I sent with the amplifier have not been returned, and no replacement tubes have been included.

I am amazed that the initial fault destroyed six tubes, so I have asked how the Distributor tested the tubes to determine that they were faulty.  I am now left with an amplifier that doesn’t work and 10 expensive vacuum tubes missing somewhere in Australia.  I am also left with a conundrum, if when I finally get my tubes back and use them to ensure the amplifier works, what happens if it doesn’t.  Will AR then blame me for any fault that occurs on power up because I haven’t purchased tubes from them at their heavily marked up prices????

For me I will never touch another Audio Research product for as long as I reside on this planet.  I will be telling all my audiophile friends and putting this report on every forum that will publish it.  Best of luck for the future Audio Research and may you drown in your policy mess!!!

128x128thazeldean
Not having owned ARC products so skin in the game, besides the glowing recommendations, it seems from reading Agon that ARC is a bit on the higher side of average in terms of needing repairs.

I'm not sure this is accurate in terms of percentages. It's simply a matter of supply. A manufacturer who sells 1000 units probably will have more service issues than a manufacturer who sells 100 units.
ARC sells more units than almost any other tube manufacturer out there, hence, with a similar 1-2% failure rate, they would have more units impacted than other manufacturers.

Personally, I've owned two ARC preamps with no service issues at all.
I've owned 3 BAT preamps, and they all had to be serviced.
Am I ARC lucky, but BAT unlucky? Who knows?
jmcgrogan2, your experience certainly trumps my conjecture. I vaguely  remember reading a few post where people mentioned that when their ARC blew a tube they sometimes take out resistors.  Maybe the fuse doesn't blow first? This may have been just with a particular year/model.  Or bad memory.

A blown tube taking out on of its resistors is not uncommon. For many years I owned a pair of AirTight ATM-2s setup for mono. These drive the tubes really hard and would blow all the time (usually when I wanted to show the system off 😏) taking out a resistor as they did in a fine display of sparks and smoke. Anyway turn the amp over unscrew the cover and it was ten minutes work to solder in a new resistor - so if you are going to rely on this sort of "protection" the least you can do is make it easy to fix!
You ignored ARC 's recommendations and instead rolled tubes on your own. ARC gear is not designed that way.  Your poor judgement, your error, your problem..