2. amps-preamps
  3. 137281-115924

New to this. How do I stack my stuff?

I'm new to hifi. I've asked a lot of questions here and some of you may already know my situation but I got the following by chance and for free: Audio Research LS16 tube pre-amp, Arcam CD92 cd player, Madrigal Proceed HPA2 amp. 

It is all up and running and I'm loving it. Now just trying to maximize the little things that I can. For instance, speakers had spike stands but spikes were missing so I made a set.

Now I read in the CD manual that it recommends sorbothane feet and says sound quality will be better.

I'm now figuring out that placement of components is important and that proper stands, expensive ones, are best. Well, expensive stands are not going to happen. But I can try to make accommodations that are cheap and won't turn the room upside down.

Here is how it is all situated now...let the ridicule flow, but keep in mind that I am space limited to a serious extent. Was not sure I'd get the system in my house at all:

The (very) heavy Proceed amp is sitting on a carpeted floor on strips of wood which raise the bottom of it well above the carpet. It is higher above the carpet than it would be above a hard surface just on its own feet.

The CD player is sitting on a small, simple, wooden, antique side table. It is sturdy. The pre-amp is on top of the CD player. I have no idea what this might mean in terms of SQ but the CD player actually puts out a fair amount to heat which rises up into the pre-amp of course. That concerns me.

So other than getting some sorbothane feet for the CD player, what else would be a priority here?

Finally are there issues with which cables contact which cables, how much speaker cables are looped, etc. (Most of the cabling is Transparent Super Bi-wire.)

Thanks for any assistance.
n80
n80 OP
2,116 posts
 
djones, I'm fairly handy with wood. I can't do anything fancy but I build built-in bookshelves with simple lines. There are plans to put built-in shelves where my system sits now but that project is months down the road and will require a re-design to accommodate this system (and for my wife to get used to the idea that it is staying.)

wloeb, that unit does not look bad at all (I was thinking steel and chrome) and it certainly is cheap. I'll let my wife take a look at it and see what she thinks. It is cheap enough that if it gets put aside when I build the built-ins it wouldn't be a huge waste of money. It says it will hold 75 pounds. I'll check the specs on the amp. It feels like it weighs 200 pounds but that is because all the weight is in the front. But I'm guessing 50 pounds.

What puzzles me about a rack is that structurally it is tying everything together which I thought was what you wanted to avoid. I suppose using some sort of isolating feet on each component might help that.

whart, I read that article. And it helps understand what is at stake but it did not seem to clarify whether the goal is isolation or integration. You guys have to admit that using graphite (very hard) in one application and rubber-like materials in another is confusing. I guess experimentation is key here.
Post removed 
n80 OP
2,116 posts
 
Thanks. I wouldn’t cut the speaker cables anyway. They have a thick outer coating and the ends have thick shrink rubber bonded to the cable end and the spades.

The speakers are out in front of all of this so no direct sound from the speakers should effect the components but I’m sure reflected sound and vibration through the floor does.

In my limited understanding of all this, it seems like isolation is the goal. To that end, it seems that 'disconnecting' the table from the floor would be better than, for instance, spiking it to the floor. It would seem to me that the table (which is quite sturdy) would be best on some sort of compliant, broad feet (even typical furniture floor protectors) that sit on top of the carpet. Again, I have no TT that needs to be stable.
n80 OP
2,116 posts
 
Shoot, I don't think that Monoprice rack will work. And my wife thought it would be okay for a temporary thing. The amp weighs 94 pounds and it will barely fit on the dimensions of the shelves because it is 19.5 inches front to back.

I'll have to look at some others but doubt I'll find anything cheap that will hold that amp.
shadowcat2016
132 posts
 
It’s not fancy, but it’s dirt cheap, quick and solid............cinder block with board shelving between them. You can go wide or straight up depending on your setup.......and wife. You can paint or stain the boards, even paint the block to dress it up for the time being. It will hold anything, even your back-breaker amp. It’s temporary and when you don’t need them anymore you can reuse them for some other project or toss them at very little loss. Don’t cut your cables, one day you’ll need that extra couple feet and have to buy a new set..........Do not stack gear on gear or put them in an enclosed cabinet. Heat kills electronics faster than just about anything, especially that monster amp of yours, they have to be able to breath. Do whatever it takes to get Mamma on board. In the long run having her on your side will make the hobby much more enjoyable for both of you............Take your time, you don’t have to get everything "right" this week............I’ve been playing with my stuff for 45 years, it’s part of the fun of the hobby.
More to discover