New to this. How do I stack my stuff?


I'm new to hifi. I've asked a lot of questions here and some of you may already know my situation but I got the following by chance and for free: Audio Research LS16 tube pre-amp, Arcam CD92 cd player, Madrigal Proceed HPA2 amp. 

It is all up and running and I'm loving it. Now just trying to maximize the little things that I can. For instance, speakers had spike stands but spikes were missing so I made a set.

Now I read in the CD manual that it recommends sorbothane feet and says sound quality will be better.

I'm now figuring out that placement of components is important and that proper stands, expensive ones, are best. Well, expensive stands are not going to happen. But I can try to make accommodations that are cheap and won't turn the room upside down.

Here is how it is all situated now...let the ridicule flow, but keep in mind that I am space limited to a serious extent. Was not sure I'd get the system in my house at all:

The (very) heavy Proceed amp is sitting on a carpeted floor on strips of wood which raise the bottom of it well above the carpet. It is higher above the carpet than it would be above a hard surface just on its own feet.

The CD player is sitting on a small, simple, wooden, antique side table. It is sturdy. The pre-amp is on top of the CD player. I have no idea what this might mean in terms of SQ but the CD player actually puts out a fair amount to heat which rises up into the pre-amp of course. That concerns me.

So other than getting some sorbothane feet for the CD player, what else would be a priority here?

Finally are there issues with which cables contact which cables, how much speaker cables are looped, etc. (Most of the cabling is Transparent Super Bi-wire.)

Thanks for any assistance.
n80
Thanks. I wouldn’t cut the speaker cables anyway. They have a thick outer coating and the ends have thick shrink rubber bonded to the cable end and the spades.

The speakers are out in front of all of this so no direct sound from the speakers should effect the components but I’m sure reflected sound and vibration through the floor does.

In my limited understanding of all this, it seems like isolation is the goal. To that end, it seems that 'disconnecting' the table from the floor would be better than, for instance, spiking it to the floor. It would seem to me that the table (which is quite sturdy) would be best on some sort of compliant, broad feet (even typical furniture floor protectors) that sit on top of the carpet. Again, I have no TT that needs to be stable.
Shoot, I don't think that Monoprice rack will work. And my wife thought it would be okay for a temporary thing. The amp weighs 94 pounds and it will barely fit on the dimensions of the shelves because it is 19.5 inches front to back.

I'll have to look at some others but doubt I'll find anything cheap that will hold that amp.
It’s not fancy, but it’s dirt cheap, quick and solid............cinder block with board shelving between them. You can go wide or straight up depending on your setup.......and wife. You can paint or stain the boards, even paint the block to dress it up for the time being. It will hold anything, even your back-breaker amp. It’s temporary and when you don’t need them anymore you can reuse them for some other project or toss them at very little loss. Don’t cut your cables, one day you’ll need that extra couple feet and have to buy a new set..........Do not stack gear on gear or put them in an enclosed cabinet. Heat kills electronics faster than just about anything, especially that monster amp of yours, they have to be able to breath. Do whatever it takes to get Mamma on board. In the long run having her on your side will make the hobby much more enjoyable for both of you............Take your time, you don’t have to get everything "right" this week............I’ve been playing with my stuff for 45 years, it’s part of the fun of the hobby.
I think I may combine ideas here. I think I might buy the Monoprice rack linked to above ($90) and just make an amp stand and have it sitting down low beside the rack. There are dedicated amp stands for $50 or more but even many of those low end ones aren't rated for 95 pounds and making one would be super easy and it would be nearly invisible under the amp.
A 95 pound amp is heavy, but even plywood would support it with 4 feet or spikes or whatever you want. That's less than 25 pounds per corner. 3/4 ply or just about anything else that you wanted to build, butcher block, layered plywood, whatever. It's a small, low, simple platform, so even a scrap of granite counter top from a local shop could work if you could cut it down to size.......really not that difficult with the right tool. ....have fun with this and include your wife in the process when possible. Buy a couple of her favorite CD's and let her see how great they sound on the new gear. Explain to her why you're doing what you're doing and why x-y and z matter......Did that with my wife and it went a long way...........If mamma is happy, you'll be happy.