Ohm Walsh Micro Talls: who's actually heard 'em?

Adding powered sub that goes down to 20 hz or so no problem and can be integrated cleanly with mains probably has the most up side if done right to throw more at the problem to increase clean output levels possible.

More power and current to the amp as I mentioned above is another. That should deliver better macrodynamics and fuller extended bass down into the 20-3ohz range for so with larger OHMs in matched size room (see teh chart on OHM site that matches models to room size), maybe talk to JS. He could probably help confirm if teh speakers are capable of meeting goals alone in target room with the right amp or not, in which case the sub route is needed. OR, he now makes model 5015 for a few grand more with powered sub built into each cabinet along with 5000 drivers.

More power and larger drivers is always the key with OHM Walshes. ONly question is how much needed in a particular case and is there a model that scales up enough alone for a particular room to meet goals.

Yeah amps AND subs - anyone like to contribute the $$ to make this all happen?! 8-)

Oh my, this will take awhile.

-Al

Coot, my 5s are limited in a manner similar to what you describe if I use my 180w/ch TAD Hibachi monoblocks in place of my Bel CAnto Ref1000ms.

The TADs do pretty well with my 100s in our large open family room/kitchen area that opens up to the whole first floor of our 3000+ sq. foot home. At higher volumes though not even close to the 5s off the ref1000m amps downstairs in the 20X30 L shaped room, which does have doors and is more acoustically sealed.

Big, natural, clean sound at realistic volumes does not come cheap, unfortunately, especially in a larger volume area/room. Its the one thing that truly justifies a lot of the money spent towards the goal of the "ultimate sound" IMHO.

Class D amps will be your friend towards this end with the OHMs when the time comes. Either more power to the 5000s and/or adding powered subs, which by the way mostly all also use Class D amp power these days.

Its basic physics. Big sound needs bigger drivers and speakers and more power and all that ups the cost.

Modern OHM Walsh design speakers are without match I find in terms of their ability to go loud and clear (with the necessary amp behind them) for teh particular size and at the particular price point of each.

I think a lot of that has to do with the Walsh driver principle as JS has implemented enabling more output from any particular driver than might be possible using typical pistonic motion only driver design. If one reads up on Walsh driver operation principles, I suspect that is a result of the fact that sound leaves the cone at different frequencies from different locations along the cone. Also because the Walsh driver does not cover the higher frequencies, above 8Khz.

Lincoln Walsh's original design attempted to be full range. It succeeded fairly well at that but all implementations at the time were quite delicate and fragile and easily destroyed at high volumes if things went wrong.

Modern similar designs, like Dale HArder's, might have solved some of those problems, or I am confident at least are able to address them better to some extent, using modern technology advances at his disposal today that did not exist in LW's day.

Remember though that the largest modern OHM Walsh driver, like the ones in my F5s3s, appear to be only about 10" or so. I have not encountered it yet practically in my case, but that will become a limitation at some time, even if the design manages to squeeze the most possible out of a driver that size.

10" and even 12" bass drivers (not even wider range like modern OHM Walsh CLS) used to be common years ago, but few modern speakers use driver's larger than 10". Many modern speakers, including OHM to some degree, tend to use smaller drivers and be less efficient in order to fit better into most people's homes. Smaller lower efficiency speakers put more burden on the amp, especially to deliver high SPL full range sound in larger rooms. Huge, heavy, and expensive monster power amps, available to few, used to be needed. No longer the case however with modern Class D amp technology, which I consider to be one the greatest recent innovations in home audio technology. A perfect match made in heaven for JSs modern innovations with the Walsh driver principle.

The sky is the limit now for home audio enthusiasts with Class D amps. Especially when you toss a few into a sub cabinet along with a good quality 12" or 15" bass driver.

To clarify one point re: adding subs. I actively cross my set up at 72hz - that number reflecting the smoothest FR I could manage thru the x-over region. I suspect that diverting those large excursion signals below 72hz away from the Ohm allows for a greater sense of macro-dynamics. The really long excursions are now executed by the Rythmik subs which handle the job better. Freed from that work, the Ohm can handle its job better, too. The increased bass extention into the bottom octave is less important to me, since it's so rarely present on any of the music that I listen to. Since Coot's a pipe organ guy, it may be more useful to him - provided he's got one (or more) of those rare recordings that actually provides the bottom end of the pipe to a system that can handle it.