Pass Lab x2.5 preamp owners -- plse help


A week ago I purchased a 1 year old x2.5 to replace a adcom gfp-750. I notice more detail in the mids and highs, bass has improved but my system sounds more 'bright'. I'm using a Proceed HPA-2, Naim CD3.5 and flatcap. have @ 300 hrs on new acoustic zen satori speaker and Matrix Reference XLR between pre and amp. Signal Cable power cords except to CD player. Focus Audio FS688 speakers with empirical jumpers. Naim recommended I plug all of this into a wiremold power strip, which i've done. When I was using the adcom-the mids/highs seemed more etched but not as bright sounding. I would like to someday move up to a Pass Labs amp, but in the mean time would like a cheaper alternative. Would a different power cord tame some of the brightness. Or maybe there just isn't good synergy with the Proceed? Before buying the Pass I didn't read anything saying that brightness was part of its 'sonic signature'. Thank you for any and all advice.
classical1
I am a Pass Labs X2.5 preamplifier owner, as well as a Pass Labs 250.5 amplifier owner, and in my system the Pass components are detailed, but rather warm sounding. If I remember correctly your prior preamp could be configured as a passive preamp. If you were using it as a passive preamp then you have probably gotten used to rolled off high frequencies and this seems like too much information in comparison. Also, as you have already mentioned, the Pass X2.5 preamp may not be a good match with the rest of your components.
power cords make a big change in my system. i too had the adcom prior to my 2.5. i have also used signal cable cords. my favorite power cord for the money is $159 for a 4ft cord from rs audio... smoother sounding - not rolled off. i would not call it a tone control, but things are smoother. the low end is not as "full," but more under control. enjoy.
I've owned the X2.5 and the X-1 and both are near identical in sonics and thought them both to be quite neutral. At least with my line conditioners plugged into them.

I'll guess two possibilities as to what you may be experiencing:

1. Your system's sonic presentation is not properly weighted between the bass and high frequencies. Now with a preamp that allows more of the high frequencies to pass thru, the impression is the presentation is even more unbalanced. You seem to have already alluded that this could be a possibility. And it most likely is the bass that needs beefing up. Again, as you seem to indicate, this may best resolved by different amplification.

And/Or

2. The ics and scs you are now using may be adding much grain, glare, and/or a digital hash. And again, the X2.5 will present more of this. I've owned the AZ Satoris as well as the Harmonic Tech Pro 9's. Same engineering principles, design philosophy, etc.. Not bad cables I suppose. But with the Audience Au24 speaker cables, the improvement were rather tremendous and much of that grain, glare, hash, etc. disappeared.

Essentially, the rest went away when I inserted the Au24 ics. Prior to that I owned Pure Note Epsilon Ref ics which were slightly better than the Harmonic Tech Pro Silway Mk II and Magic Link One ics prior to.

That may well take care of much of your problem. And if you did pursue the Audience Au24 line up, with a little work on your part, you should be able to get all of the Au24s for about the same price you can sell your existing cables.

Or for just a fraction of the price, you can try the new Anti-cables by Paul Speltz. These are easily the best speaker cable I've owned thus far (I've had them for two weeks now) and they only cost $60 for a 6ft pair.

To take care of the rest of any electrical-related issues, you should consider proper line conditioning.

-IMO
Hi,

I owned the X2 and thought it was neutral with a liquidty airy presentation not bright at all. I woud suggest selling your Proceed amp and getting a c-j MV-60, Quicksilver Mid-monos, or AES Sixpacs tube amp and your system will start to sing.

Good Luck!
I have owned the X-250 and X-1. What is descriped above is accurate on their sound. When I tried the combo in a buddies system, it did not work and I heard the brightness that you heard. If I recall correctly, it seemed to come from the matching of the Pass gear to his speakers. There seemed to be a certain frequency that was moved forward in the presentation that made the system sound bright. I was using an Elrod EPS Sig 3 power cord so I felt that it was not the power cord. It also could have been the speaker cable and ICs. They were AZ Sil Ref ICs and Home Depot speaker cable. The Cardas Golden Hexlink 5-Cs seemed to reduce the edge or brightness. I'd try a few different cables to see if you can get ride of the brightness and if they don't work, it could be a speaker matching issue.

Happy Listening.