PS Power Plant or Alan Maher PE's?


I've reached the point to where my power should be addressed. However i am really lost as to what direction to take. The best PC I have is the Iron Lung Jellyfish which is really inexpensive. I have tried some more expensive cables but was not impressed. But i know that power makes a difference. I do have a dedicated circuit with an Arrow Hart recep. Not the best but not bad. So where do i go from here. Obviously i should replace the AH recep. But then what? I was set on the PS Audio power plant premier. Then I've heard about Alan Maher's PE's and other filters. The question is which is the best? I know that the power Plant separates the digital from the rest and is a regenerator which seems to be what I need. But I'm not very familiar with Alan Maher's stuff and his website is less than informative. That said, which one should i go for?
My system is listed
128x128artemus_5
Nsgarch Thanks for your info. I do have a few questions however. How will the apc power supply effect the sound? Would I be better to not leave my amp and sub woofer on? I can't turn off the preamp because it has no on/off switch so that presents a problem,
Nonetheless, I know these interruptions can't be good for equipment. I do have a surge protector (Monster) so maybe it is keeping the equipment safe.
Artemus, it's not a great situation you're in, but what can you do? ;-) You have an all solid state system, so in theory, it shouldn't hurt anything to leave it "always on"; all of it, unless it's drawing too much current at idle, but I bet it's roughly two 100W lightbulb's worth for the whole system.

I never got that much into the details of UPS's, not even with my computers, because frankly I haven't had to. So your best source for information is the manufacturer. The trick is knowing what questions to ask;-)

I would first explain that you have an expensive audio system which you'd prefer to leave "always on." That you'd like protection from ordinary surges, but that your real problem is from momentary power outages; specifically the damage that quick power turn on can cause to equipment which hasn't had a chance to fully shut down before restart. And do they have units which address that issue; meaning units which inject full power INSTANTLY so your equipment remains on, whether idling or in use, as if nothing happened? And of course, would there be any affect on sonics, especially when the unit was just in 'standby'?

I wish I could say more, but life is all about asking the right questions, so maybe that will get you started . . .

Neil
.
Nsgarch. thanks for your reply. I am 100% with you in the importance of asking the right questions.
I may speak to the power company as well since I think this situation is somewhat ridiculous. Yes, I live in the mountains, but I live in a town of about 50k and my house is only 13 yrs old. Fortunately i know and am about to do a job for the person who schedules new service installation for the power co. Maybe I'll ask him about it. Unfortunately the pole which feeds my home is covered with vines which can't be good and may be a large part of the problem. Anyway, thanks for the heads.
I spoke to couple of techs about using a UPS. Multiple problems here: First of all they were designed for computers, not sensitive audio equipment. Secondly, most UPS's can't handle the draw of some big amps. I know that even the UPS for my server was not big enough to handle a pair of servers and this was a fairly hefty UPS.
The batteries in them are expensive. Third and final note, when I was really drawing on my UPS, the current wasn't quite up to "par". It is designed to allow for proper power down of a system, not to continue running it. I'd bet that running a turntable or cd off of a UPS in protection mode will go at lower rpms?
Elvick, I don'tknow what UPS equipment you were using, though I certainly am aware they had (past tense;-) certain shortcomings with respect to AV systems. But times have changed. APC (and probably others) have entered the AV market with products like these http://www.apc.com/products/apcav/index.cfm