Received The MC2000 Back From Expert Stylus Today
So I got the Ortofon MC2000 back from Expert today, and Mr. Hodgson did a beautiful job on this service. He fitted a new Paratrace stylus and made a minor repair to the end of the OEM cantilever. Looks as new, and there are no oddities to the stylus assembly. The Paratrace diamond is quite diminutive, barely able to be seen with my aging eyes.
This afternoon I installed it on a very light Fidelity Research headshell, looks kind of like one of the Swiss cheese SME ones. Wired it to a T2000 transformer and then to a Graham Slee Accession.
This is a remarkably detailed and neutral sounding cartridge. I have a few decent cartridges here and this is as good as any I have experienced. My system uses a pair of JBL 4365 speakers and a Halcro DM8 pre amp, so I have to be careful with system synergy as a too clinical component can push it over the edge. The MC2000 comes very close to doing this. I am considering a wood headshell like the Yamamoto boxwood, due to its low mass and its ability to add a touch of warmth/body to the overall sound.
But even as it sits the transparency, the fine detail, the dynamic contrasts are all outstanding. I can tell after an evening of listening this is a keeper for me, and while its been a bit of a drawn out journey to accumulate the bits and pieces and get the cartridge serviced...well...it was worth every bit of effort.
Yes I enjoy my Transfiguration, ZYX, and Ikeda, that is true. But I like the MC2000 every bit as much and I would get rid of a whole bunch of stuff before I ever parted with this cartridge.
Hi neonknight, As J. Carr explained the only advantage of aluminum cantilever is that the stylus can be ''pressure fitted'' while by all other (''exotic'') kinds the stylus must be glued in the cantilever. This means glue between stylus and the cantilever which compromise rigidity of the combination. |
Dear Nandric, I do refer to the MC2000 that I bought from you. I thought you told me it was re-tipped by Axel with one of his last assemblages (cantilever and stylus) that either resembled the original or was per original Ortofon spec. If it IS original, then all the nicer. Definitely an aluminum cantilever with press-fitted stylus; I've examined it under my microscope. As you already know, it is a favorite. Based on other writings of JCarr, I would think it is best to stick with Aluminum, since the suspension, etc, was designed with the mass and flexibility of aluminum in mind. But I would be curious how it would sound with sapphire or boron. Sapphire would be closer to aluminum in mass, I think. |
Dear @lewm : Boron cantilever puts the 2000 in a higher step on overall quality performance. I made the comparison against an original one. I owned 3 of those cartridges. VdH made the work. Boron stiffer material helps with the resonance tonearm/frequency due that we have to remember that the measured compliance of the 2000 is over 30 cu and this means that that resonance frequency with high mass tonearms will be at 4hz-5hz.
R. |
@lewm So if the MC2000 you have indeed has the factory stylus, do you have any idea of hours? The cartridge is now pushing 40 years old. Ortofon states their diamonds start to show wear at 1000 hours and are definitely done at 1800 hours. If you are at the end of the lifespan, what would you do for a replacement diamond? @rauliruegas If I had a MC2000 that had a damaged cantilever I would consider a refurbishment with boron. But in the case of my cartridge I would not replace the OEM aluminum cantilever, there are getting to be fewer and fewer of these cartridges in good working order. In my case I have the Ortofon case,box, headshell, screw drivers, scale, stylus brush, bolt container, graphs, and even lapel pin that came with the original purchase. I also have the T2000 transformer, box, and paperwork. So having a complete original combination is of value to me, and having the MC2000 restored to as close as OEM condition as possible makes the most sense. If I find a body that is a good candidate for surgery, then I would do it.
|
