VPI service problems


Am I the only one having a problem with service from VPI? After buying
a HW-27 Typhoon record cleaning machine from them based on the positive
reviews and recommendations of all the audio mags (not an inexpensive
purchase) and using it carefully and sparingly and enjoying it
immensely, the vacuum motor blew out it's gasket and began leaking like
a sieve. I was disappointed but thought OK stuff happens. Then my real
problems began. To say that their after the sale service is lacking
would be a huge understatement. Emails went unreturned for weeks,
attempts at phoning resulted in many messages left ignored and then
being told that they only respond to email inquiries, which again go
unanswered for weeks! Contacting all of their authorized dealers
doesn't help as no one seems to be able to get or stock the parts and
they tell me that it would take weeks for them to get them as well.
Finally after five months of effort I received my replacement motor
(which cost $240 plus shipping) and now six months later the second
motor has blown it's gasket and is leaking all over the place again and
I am right back to square one. No returned emails for weeks and weeks
and a pricey record cleaning machine ($2200) that is inoperative and
will be down for months and months again. Is their business so good
that they can just ignore their customers? Are the dealers really
unable to help as well? Am I the only one with this problem? Anybody
have any thoughts or ideas on how to help?
128x128dcbluesplayer
I've called VPI on several occasions and they are always rude. They act like they are doing you a favor by answering the phone. Thank god not all audio companies are like this.
I have to say I've called VPI on several occasions when I was putting (my bought used) VPI table together and always got great results. I recall that they had limited hours though, something like Tues.- Thurs. only. I believe Mike was the one I talked to when I asked for customer service. He was always very informative and answered all my questions.
I have been in corespondence with dcbluesplayer, and there are some facts that may complicate service. One, the machine was said to be bought direct from VPI. In that instance, I'm unsure just how much dealer support a dealer will give, going to bat for somebody who bought direct?

Also, it was mentioned the machine was out of warrantee when it first failed. I gather from our conversations that the entire machine was sent back for service.

While I know from personal experience that VPI will many times, fix, or issue parts to a customer free of charge, even outside the stated warrantee, I would imagine that if they constantly gave out very expensive parts for free every time, they'd go broke in short order.

Generally, I believe them to be very fair, that if the part, or manufacturing process was at fault, they will replace, or repair free of charge. And it is understandable that if a product, even while under warrantee is damaged by the customer due to whatever reason, that this may indeed void such warrantees.

In our conversations, we have discussed alternatives for a need to investigating, and buying parts from other sources. VPI of course does not manufacture either motor in their RCMs.

It appears the current VPI 16.5's uses an Ametek Lamb Rotary Motor. And they can be gotten for less from other distributors. I would assume the two other models VPI make also use the same brand of motor, but perhaps a different model?

Whether the Tyhoon, with its higer CFM-Vacuum rated motor creates a problem with fluid intrusion into the motor, that the higher suction causes fluids to somehow bypass the internal baffle system of the recovery tank, I cannot honestly say?

It could be as well possible, that fluids containing certain chemicals in them, such as high concentrations of alcohol could possibly be a detriment to the rubber gasket seal between Vacuum Motor-Recovery Tank?

I would imagine these simple foam rubber seals should be a part that should be able to be easily gotten from VPI at at a small cost. And that over time, parts such as these, regardless of care will eventually deteriorate-fail.

If a recovery tank perhaps has some fault with internal baffling, I would imagine this could be one cause, with shortening vacuum motor life. There are certain guidelines with operation of these RCMs, and VPI should better explain in their manuals what those are.

Draining the tank, clamping drain hoses tight, and leaving the wand off the machine until innards are totally dry are just a few.

And periodic internal inspection should be done. Don't be afraid to open up these manchines, it may save you money in the long run. Mark

OK, here is the latest update. I initially emailed VPI on June 28th and have yet to have an adequate response, I mean 19 days later and seems that it is WAY too much trouble to even bother to answer their customers emails! I have sent several follow up emails over the last couple of weeks to Mike's attention in their service department but they have been ignored as well. Just can't seem to break thru the barrier that Sheila puts up to get to anyone who can or wants to help.

Just when I thought that I was totally on my own, a couple of the forum members have come forward to try and help (isn't it great when the Internet works like it is supposed to). Thanks to some combined efforts we have discovered that VPI sources their vacuum motors from WW Grainger and after a couple of calls to them (thanks to JR in the Grainger customer service department) I found that the vacuum motor VPI uses in the HW-27 Typhoon is an Ametek Lamb model 116757-13, Grainger found one locally for me and I was able to pick it up on one days notice. But the best part is that they charged me only $72.61 for the exact motor that VPI charged me $240 for last time! Don't you think that a 250% mark up is a little steep? What a rip-off. Now if I could just find who sources the foam gasket that goes between the motor and the catch basin I will be good to go. Anybody have any ideas on where to get one?
DC, As I mentioned, McMaster-Carr handles rubber, and foam rubber in about 12 different types. Can be gotten in adhesive backed, or non-adhesive backed. And the sizes are so diverse, one can find anything one wants.

I suspect VPI used a "lowly" Neoprene Foam Rubber Gasket, and this what it appeared to be on my own 16.5 RCM.

After all, the RCM isn't the space shuttle, so no need probably for ultra high temp, or flame resistant foams, or other ultra space age qualities needed.

Neoprene Foam Gasket will probably offer the best of all worlds, being resistant to any chemicals encountered with record cleaning, and the temps as well. The only thing I am not sure about, would be the Shore Hardness of the foam rubber, but they do have a scale, with descriptions.

As to how wide, long, and thick, a simple ruler will tell you that basically. I would suspect a 4" wide strip 24"-36" long would be in essence a lifetime supply. You would then have ample to custom cut the gasket with scissors-X-Acto Knife, peel the backing, and apply.

While your at it, buy yourself a 12"x12" sheet of 1/16", or 3/32" Neoprene Sheet from them, rip the cruddy Cork Mat off, and be done with the cork forever, like I have done.
If you have 2-3 RCMs to do, no prob, they can sell you a cut sheet 12"x36, which will be enough for 3 machines. The neoprene will last a lifetime, is easier to clean, keep clean, and identify dust-dirt.

The Cork Mat IMO was a poor choice.

I went with non-adhesive backed finally, as the first time I bought, and tried it, I went with an adhesive backed neoprene sheet from them, it was a little lumpy. It wasn't bad, and would've worked fine, but I am a fussy bugger, and wound up gluing the neoprene to the custom acrylic platter with Contact Cement.

The details of Mat installation are covered in full on AIVS's website, under "RCM Museun".

Keep us posted how this all turns out! Best of luck, Mark