Eminent Technology ET-2 Tonearm Owners



Where are you? What mods have you done ?

I have been using these ET2's for over 9 years now.
I am still figuring them out and learning from them. They can be modified in so many ways. Bruce Thigpen laid down the GENIUS behind this tonearm over 20 years ago. Some of you have owned them for over 20 years !

Tell us your secrets.

New owners – what questions do you have ?

We may even be able to coax Bruce to post here. :^)

There are so many modifications that can be done.

Dressing of the wire with this arm is critical to get optimum sonics along with proper counterweight setup.

Let me start it off.

Please tell us what you have found to be the best wire for the ET-2 tonearm ? One that is pliable/doesn’t crink or curl. Whats the best way of dressing it so it doesn’t impact the arm. Through the spindle - Over the manifold - Below manifold ? What have you come up with ?
128x128ct0517
Hi Grant – welcome to the thread. Another New Zealander. I wish I was there right now.

With both Mark and yourself discussing Medo’s I dug out my medo ac0110 pumps from the past today and hooked them up separately and together to experiment. I remember I received them with three wires hanging. I cut off the three prong from two power cords and spliced them to make the wall plugs. So I did connect their grounds. I was only using one at the time and the other was a backup.

Separately mine both produce about 12 psi on a pressure gauge inserted within a few feet of tubing to the ET2. A real dynamo of a pump for only being a couple inches by a few inches.
When I connect them together on a T Valve PSI only goes up to about 15 psi as they are working against one another. Hopefully someone else can chime in if they are using two Medo’s. I went to the Timeter pump after the single Medo. The Medos are a linear piston design if that helps. Maybe Dover if he sees this can offer some advice as he used multiple pumps with his ET2 setup.
Cheers Chris
Hi Chris/Grant
Yes I used 2 pumps running into a 20 litre surge tank. On the pumps I used, reversing phase & neutral at the transformer inside reversed the phase on one of the pumps. In NZ you must not reverse phase and neutral at the power cord because the mains fuse must be in the phase line.
Hi Chris/Dover

Thanks for that information very helpful.

I have an ET2 with original low pressure manifold so I think 12 to 15 PSI if anything may be too high. The original pump did not like 50Hz, managing typically less than 4PSI.

Have filters and a pressure gauge, but not sure what a "regulator" is and locally what industry would be the best source for a suitable unit.

As the pumps are 115V, 50/60Hz I briefly considering running the two pumps in series, one "out of phase". I thought better to run them off a step-down transformer in parallel. Pumps would be housed inside a baffled box so effectively double insulated and isolated from one another, with the surge tank also housed in the same box.

For the surge tank I was going to use PVC pipe and fittings (2 - 300mm lengths of 200mm dia pipe with sealed end caps). Any advice on packing, was going to try some left over "BATTS".

Am I on the right track?

Many thanks for the advice.

Kind Regards

Grant
You've just reminded me - I got a big improvement when I put an isolation transformer between the mains and the pumps. Much smoother sound.
Have filters and a pressure gauge, but not sure what a "regulator" is and locally what industry would be the best source for a suitable unit.

Hi Grant - this picture shows a

regulator (black top dial knob), moisture bulb and trap, pressure gauge

They can be purchased separately or as a unit at any hydraulics place typically located in industrial areas.
Total cost about $70 us dollars. The regulator allows you to dial the pressure down or up. The one in the picture is portable. You can hold it in your lap sitting in your sweet spot, and adjust the pressure up or down and hear how the music delivery is affected.
You open the regulator by lifting up – turn clockwise and counter clockwise. When the music sounds best to you in your room – push it back in to lock – your done.

As a kind of tune up I personally recommend anyone with an ET2 send alot more air than is needed to the tonearm so you can determine if you have any leaks from screws/bolts. This tonearm was meant to last forever – its industrial quality just like Bruce’s subwoofer :^)

subwoofer

The worst thing you can do is blow the tube off.

Bruce Thigpen can also replace your low pressure manifold for a high pressure one. This changes out the manifold only – the spindle stays so you are left with a high pressure ET2 not a ET 2.5. I recommend emailing him to get the current price which is very reasonable. The high pressure manifold allows you to run low and high pressure with the ET2.

Cheers