Help With 60Hz Hum PLEASE


Greetings,

I am having some issues with noise coming through my speakers at low volume. The noise sounds like a 60hz cycle hum, and can be heard clearly when the volume is all the way down. I have tried several things to quiet down this noise, but nothing has worked so far.

Before I give details of action items I have tried, let me inform you of the components I am running.

My system consist of:

·     AV PRE/PRO MARANTZ 8801

·     AMP ADCOM GFA-7805

·     SONY 300 DISC CD CHANGER

·     SPEAKERS B&W CDM9NT/CDM CNT/CDM1NT

·     SUB VELODYNE SPL1000 SERIES II (NOT HOOKED UP AT THIS TIME)

·     USING XLR INTERCONNECTS BETWEEN PRE-AMP AND AMP (MONO PRICE)

·     DEDICATED OUTLET CONNECTED TO 20AMP CIRCUIT BREAKER

·     FURMAN POWER CONDITIONER (EVERYTHING PLUGS INTO THIS)

·     I SEGREGATE OUT THE AC POWER LINES FROM THE SIGNAL AND SPEAKER CABLES


So this is what I have done to check the system so far.

1.   First off I separated all of the components power sources, plugging each component into its own outlet with the amp plugged into the dedicated outlet. (NO CHANGE, NOISE PRESENT)

2.   Unplugged any no essential item leaving just the pre-amp and amp plugged in (NO CHANGE, NOISE PRESENT)

3.   Removed the amp from the system, plugged in single source and speaker set (NOISE IS COMPLETELY GONE!!!)

a.   FOR ABOVE TEST I USED MY IPHONE WITH A SET OF RCA INTERCONNECTS STRAIGHT TO THE AMP.

                                              i.   I really suspected the amp at first because about a year ago I had the unit repaired for a standby condition. The repair center I used also repaired the CENTER CHANNEL BOARD while they had the unit. I noticed that the center channel has almost no noise coming through, but after the previous findings I decided this might be a symptom not the cause of the noise.

4.   Hooked back up system and tested (CRAP, THE NOISE IS BACK)

5.   Unplugged all of the XLR interconnects from pre-amp side (NOISE IS GONE, YEAH!)

6.   Plugged in one interconnect into pre-amp (noise comes through that channel)

7.   Switched between XLR and UNBALANCED (THE UNBALANCED CONNECTION WAS A BIT WORSE)


My conclusion is that something is happening between my pre-amp and amp that is allowing this 60hz signal though. I am wondering if it could be the interconnects themselves because I am not using a high quality interconnect. All I am using is Mono Price XLR cables. Although, why would there be no noise when the cable is plugged into the amp and not the pre-amp? Might the Marantz 8801 be the culprit due to the fact that when I plug in the cable into the pre-amp is when the noise comes through? Or maybe my first instinct was correct in that the amp is the problem?

Any help figuring this out is appreciated.

Thank You Kindly,

Joe

jo3533
OK.....so I never made it all of the way to the testing sequence as stated above. I started to set up for the test, but when I get the 100lb. amp out of the equipment rack and set it on the floor. I decided to try a couple of things before I removed the rest of my equipment.

In order to shorten this a bit I will cut to what I did the gave me a reason to pause and reflect.

For this the amp is plugged into a dedicated outlet with NOTHING else attached.

I ended up plugging in my iPhone directly into the amp using 1/8" to RCA adapter. Voila, no noise at ALL!. 

So with the iPhone plugged in with RCA connectors there is no 60hz hmm. So I decided to go ahead and plug in the xlr cable into the same channel that the RCA cable is plugged into. NOTE: the XLR cables were not connected to anything for this test, they were plugged into the amp only. The noise was back, although much softer. So then I flipped the "Balanced/Unbalanced" switch to "Balanced" and the noise was back. Unplugged the xor cable and the noise is gone. 

Bottom line. Every time I plug in the xlr cables the noise comes back. Even if they are not connected to anything on the other end.

I am now, more than ever, thinking the problem is within the amp.

Any thoughts? Any suggestions? 
 

jo3533,

You cannot connect the XRL cables to the amp without the other ends of the cables connected to a load/source.

If they are not connected to a load, like a preamp, and are just laying there open ended you basically have 5 antennas picking up RFI and sending the noise to the inputs of 5 power amps.

If you have the amp on the floor that’s is definitely the hard part of the job.

The Marantz 8801 is considerably lighter.


But, before you pull the Marantz out of the rack do you by chance have an old DVD player? Or you could use your Sony multidisc player.

For a test connect a pair of RCA interconnects from the audio out of the player to the front right and left channels RCA jacks on the Adcom amp.

With the Adcom amp turned OFF,

Plug in the power cord of the player and turn it on.

You will not be playing any music through the player. DO NOT press start to play.(If you are using an old DVD player don’t put a disc in it.) By chance if a disc is in the player and you were to press play the music would be loud but not ear deafening. I still would not try it!

Next flip the toggle switches on the back of the Adcom for the front right and left channel amps to single ended. Turn on the amp.

Just a guess you will not hear the dreaded hum.

Unlike when you were using the iPhone for a test which is battery powered, the player is 120V AC powered. The player is the termination for the single ended RCA interconnect cables. Both pieces of equipment are powered from your house’s 120V mains power.


Post back your findings.

Ok, so I hooked up an old Koss CD player to my amp. fired up the CD player and then the amp. One note about this unit is that it only has a two prong plug much like my Marantz.

The noise was GREATLY reduced. I could still hear it, but is was very faint.

Just out of curiosity. Would better xlr cables help clean up some of this noise? I am using an inexpensive cable set currently.


Ok, so I hooked up an old Koss CD player to my amp. fired up the CD player and then the amp. One note about this unit is that it only has a two prong plug much like my Marantz.

The noise was GREATLY reduced. I could still hear it, but is was very faint.

Just out of curiosity. Would better xlr cables help clean up some of this noise? I am using an inexpensive cable set currently.

jo3533,

Sounds good.

You could still hear the faint noise, jmho, because the Adcom is rated at 300 watts per channel. Jmho, that’s probably the best an RCA singled ended ICs, interconnects, will do. You need to go with balanced ICs.

Hopefully Al, (almarg) is still following this thread when someone posts on it and will hopefully chime in. Al can tell you the whys you will need balanced cables over single ended for the lowest noise floor possible.


I take it you have not bought any new 1 meter or longer XRL balanced cables yet? For a test just pick up 1 pair for now. Try them between the Marantz and the Adcom amp. Connect them to the front left and right channel outs on the Marantz to the front left and right channel inputs on the Adcom amp.

Don’t forget you have to / need to separate the two from one another. I would try to get the Marantz at least 18" to 24" away from the Adcom amp.


Quote:
Adcom GFA 7805 specs:
Continuous power: 300Wx5 into 8 ohms (24.8dBW), 450Wx5 into 4 ohms (23.5dBW); both at <1% THD, 20Hz-20kHz. Input sensitivity for full output: 1.61V RMS. Voltage gain: 29.67dB. Input impedance: 500k ohms (RCA), 10k ohms (XLR). THD+noise (typical): <0.135% (8 ohms), <0.3% (4 ohms). Frequency response: 10Hz-20kHz, +0/-0.25dB at 1W, 8 ohms. Power bandwidth: 3Hz-130kHz, -3dB.Signal/noise: >112dB, A-weighted. Damping factor: >500.

Read more at http://www.stereophile.com/content/adcom-gfa-7805-five-channel-power-amplifier-specifications#jVM8Mi...

Al can tell you the whys you will need balanced cables over single ended for the lowest noise floor possible.
A properly designed balanced interface will reject nearly all noise that is present equally on its two signal lines, since a balanced receiver circuit responds essentially just to the difference between the voltages on those two lines. An unbalanced interface has only one signal line, of course, so it will not do that. Also, a **properly designed** balanced interface will be less susceptible to ground loop-related hum and noise than an unbalanced interface, since a properly designed balanced interface will not put signal current through the ground connection in the cable. Although as was said earlier it appears in this case that a ground loop is not responsible for the problem.

A suggestion that occurs to me at this point, although it is just a hunch: In addition to obtaining longer XLR cables, purchase some RCA shorting plugs and insert them into the amp’s RCA input connectors, while connecting the amp to the preamp with the XLRs. Just a hunch, as I say, taking into account that both the specs for the amp and the Stereophile measurements at the link Jim provided make it clear that the amp’s RCA and XLR inputs are received by separate and independent input stages. (If that were not the case shorting plugs on the RCA inputs would probably short out one of the two signals in the balanced signal pair).

You can find a number of sellers at eBay offering inexpensive RCA shorting plugs.

Regards,
-- Al