2. analog
  3. 124682-9953

Newb question regarding alignment - Should the stylus Physically touch the protractor?

Hi everyone,

Real quick question, im going to try (yet again) aligning my cartridge (Shure M97xE) on the stock head of a Denon DP-31L turntable. This go around I’m using a print out of an arc protractor, kindly emailed to me by Ken Willis who makes great stuff from reciews I’ve read.

My question is, when the instructions say to place the stylus on the arc, does it literally mean touching/resting on the arc or positioned just above?

Since the heaviest paper I have is resume paper (not much thicker than standard computer paper), I was thinking I’d glue this protractor printout onto an old vinyl I don’t need to provide a solid backbone, and with the tonearm still locked in its cradle I’d then press play so the Denon lowers the tone arm guard, and then turn off the table so the guard stays in the down position. All that, assuming the stylus should physically touching the arc line I printed. Of course I’ll have the platter taped down too so there is zero movement when I lower the stylus on it.

If someone could let me know whether or not my interpretation is correct I would really appreciate it

Thanks in advance for the help, clearly I’m new to this and I’d be lost without the advice of all the knowledgable folks on these forums :)

hockey4496
hockey4496 OP
104 posts
 
He just emailed me a PDF when I inquired about the correct one to use on my TT since it wasnt listed as an option. It worked out great though, dead on alignment in less than 15ish minutes 😁
elevick
2,636 posts
 
I like my Geodisc and yes I let the stylus touch-CAREFULLY.  The 97 should have a plastic guard it shipped with, you could keep that on?

Do NOT tape the platter down to keep it from moving.  If this is direct drive, not good for the motor, belt drive tough on the belt.  Unplug the table, turn the platter by hand which should lower the guard.  That will protect everything.
lewm
13,099 posts
 
You would lose accuracy if the tip of the stylus is not allowed to touch the surface of the protractor.  Adding a layer of plastic over a paper protractor might have a similar, although negligible, effect on accuracy. However if stylus force (VTF) is set at or near to the recommended value, there is no danger of damage to the stylus by allowing it to rest on the protractor; the process is exactly like playing an LP.

Elevick, Why do you warn against taping the platter so it does not move around during the alignment process? No one going through the process of set-up is likely to power up the platter while it's taped in place. Pull the plug, if you're squeamish. Taping the platter is more or less required, if you want to get the alignment as accurate as possible; if it rotates during the process, by even a few mm, you've lost the ball game.

Hockey, If you've printed out a pdf sent by Ken Willis, he probably warned you to be sure your printer was set up for a 1:1 ratio of image to print-out.  If not, you are hereby so advised.

wntrmute2's avatar
wntrmute2
188 posts
 
Best thing I have done when printing out a protractor is to print them on transparency film ( like for the old overhead projectors ) then I tape them to a light colored album such as the gold colored Grand Funk album.  $3.00 at any used record store.  If you are careful aligning the printed hole with the punched stylus hole, taping the print down securely and only then cutting out the spindle hole on the film larger than the album hole, you will VERY close alignment.  To answer your original question, yes put the stylus right on the grid.
elevick
2,636 posts
 
Lewm, it sounds like this is a semi automatic table.  The gear will force it through a cycle if the button is pushed.  You should be able to manually turn the platter to get to the perfect point in the cycle of lowering the arm having the platter able to spin without the motor actually kicking in.  That will prevent the platter from taking off and may even keep it in place.

And yes, I'm paranoid.  Too easy to bend a stylus.
More to discover