Add this to the can!
https://www.youtube.com/watch?v=RfpJYJv3ddo
Manley Chinook Features and SpecificationsVacuum Tube Complement: 6922 x 2 (gain stage) plus 6922 x2 (output stage). Any 6DJ8, 7308, ECC88 types may be used. Unbalanced Input and Output connections via Manley Teflon® & Gold plated RCA jacks Automatic Mute Timer: On initial power up output jacks are muted for approximately 45 seconds. Automatic mute circuit allows tubes to warm up and circuitry to settle. At power down, output jacks are immediately muted. Input Termination Capacitance (MM/MC): 3-position user-selectable capacitor values of 50pF, 100pF, and 200pF yield resultant combinations of: 50, 100, 150, 200, 250, 300, and 350pF Moving Magnet Input Impedance: 47k Ohms, fixed Moving Coil (MC) Input Impedance: 5-position user-selectable resistor values of 50, 100, 200, 400, and 800 Ohms. There are 32 possible loading possibilities. See "more images" for a chart: Gain: Internal DIP switches select 45dB or 60dB Deviation from RIAA curve: Less than ± 0.5 dB from 20Hz to 20kHz at any gain setting. Typically less than ±1dB from 10Hz to 100kHz. Distortion (THD+N) (47k Ohm Input Termination, 45dB gain, 1kHz sine, 0dBu output): Typical 0.010% THD+N, into 100k Ohm load, BW = 100Hz-22kHz Distortion (THD+N) (47k Ohm Input Termination, 45dB gain, 1kHz sine, 0dBu output): Typical 0.030% THD+N, into 600 Ohm load, BW = 100Hz-22kHz Dynamic Range (MM input, Gain set to 45db, 200 Ohm source): 91dB @ 1kHz, 0.1% THD+N, BW = 22Hz-22kHz Dynamic Range (MM input, Gain set to 45db, 200 Ohm source): 107dB @ 1kHz, 1.0% THD+N, BW = 22Hz-22kHz Noise Floor at 45dB gain setting with shorted input: -84 dBu, A-weighted Noise Floor at 60dB gain setting with shorted input: -75 dBu, A-weighted Maximum Input at 45dB gain setting with 20 Ohm Source Z @ 1kHz into 10 kOhm load: 250mV RMS = +34.5 dBu @ 1% THD+N BW=22Hz-22kHz Maximum Input at 60dB gain setting with 20 Ohm Source Z @ 1kHz into 10 kOhm load: 40mV RMS = +34.2 dBu @ 1% THD+N BW=22Hz-22kHz Maximum Output: +37dBu @ 1kHz, 1.5% THD+N into 100 kOhm load Output Impedance: 91 Ohms Minimum Recommended Load: 2500 Ohms Internal Power Supply: Fully regulated linear B+, Heater, and control voltage rails. Operating Mains Voltage: Units are built for original destination country's mains voltage: 100V, 120V, or 220-240VAC as indicated on the serial number badge. Power Consumption in Standby mode: 1 Watt (8.0mA @ 120VAC) Power Consumption: 42 Watts (345mA @ 120VAC) Mains Voltage Frequency: 50~60Hz Power Transformer: Toroid contruction for low radiation. Mains Fuse for 100V-120V operation: 500mA SLO-BLO size 5mm x 20mm Mains Fuse for 220V-240V operation: 250mA SLO-BLO size 5mm x 20mm Standby Transformer Fuse for all voltage operation 100V-240V: 10mA, SLO-BLO, MDL type size 1/4" x 1 1/4" Badge Lamp: LED illumination Dimensions: W=19", L=11", H=3 1/2" Shipping Weight: 15 Lbs. Recently Viewed Products
https://www.youtube.com/watch?v=RfpJYJv3ddo
Manley Chinook Features and Specifications