Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57

Thanks very much for the great rap osmium, much appreciated.

So nirvana has been achieved. The Romp by My Friend The Chocolate Cake, as one of our standard test tracks, was a special treat for our ears.
Great Aussie talent, so much of it here, undiscovered.
https://www.youtube.com/watch?v=We3HrsuqYJk


When we added the Lightspeed attenuator the difference was obvious to us both. Digital volume control (from either the Touch or MiniDSP) was actually getting in the way and also raised the noise floor (as you would expect). Adding the Lightspeed gave us deeper bass, much wider soundstage, and transparency that finally took full advantage of the Lowther’s speed. Noise floor dropped into the black.
Yes digital domain volume controls can be very good if near full up, they have to be used at or over 75%, this can be too loud for most systems. If under 75% they can actually reduce the digital resolution "Bit Stripping" to 14bit, 12bit, 10bit ect, and the lower you go, the less resolution you get.
This is why the Lightspeed Attenuator being so transparent/dynamic is great, set the digital volume at full, adjust the Lightspeed Attenuator to the loudest you want to ever hear, and then use the digital volume remote to lower the level as needed, that way your never under 75% with it, this way you'll never "Bit Strip"

Cheers George
Great clip George.  Captures what they're like live.

I figured I'd hear a difference with no bit stripping and the change in noise floor but I was really surprised by the spatial effect on the music.  The soundstage is far wider and deeper.   Very happy.

As the Lowther's are so sensitive, I was really cutting a lot digitally.  We rarely go over 50% on the Lightspeed (depends on music) and usually sit at about 1/3.  

Cheers,
Scott

Scott you could try 2 inexpensive different ways to power the Lightspeed Attenuator, that many say is an upgrade to the power pack that I use.

1: Pure dc, rechargeable Lithium battery these will last around 1-2 weeks of listening a couple of hours a day before a recharge is needed. Just make sure with the seller that it has a 2.1mm plug and centre is positive.
http://www.ebay.com.au/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.X12v+Li-Ion+rechargeable.TRS0&_nkw=12v+Li-Ion+rechargeable&_sacat=0

2: Very good mains supply, also quite cheap. (9v-15v is fine) again make sure the plug is 2.1mm, centre positive.
http://www.ab-system.hk/index.php?route=product/product&product_id=64

Cheers George

My system if a fi2A3, an Abbas DAC, and Klipsch Belle speakers so it seemed ideal for this type of attenuator.  I was expecting it to be fairly neutral since not much is being added but I was stunned by how much improved the clarity of my system was.  The quiet spaces in between the sounds are unbelievable.  I am very happy with this new addition.  
Post removed