Power supply AC cords: any reason to upgrade?


As it happens my system has three linear power supplies converting 120vAC to 5, 12 and 24vDC, and Rogue Audio Ares pre-amp with a detached-box power supply of its own. Is there any benefit to upgrading the line cords feeding these units, or can I just use the decent-quality plastic molded cords the manufacturers provide?
john_g
@john_g What do their power cords look like at the moment?
e.g. like the PC’s that are supplied with computers (i.e. skinny) or something more heavy duty?

What are the linear supplies like - good quality or el-cheapo?

Do you want Store bought or DIY?

Is the DC power cord from the supply of good quality or cheep and nasty?

Can you replace the power cord on the DC side of the power supply, or is it connected inside the case?

The drawback with units like this is that
1. unless you are a competent DIYer - it gets expensive real quick
2. they may not be worth the expense

Finally - How crazy do you want to get?

Generally - upgrading the PC’s on the small power supplies can provide better sound quality, but the cables you can purchase tend to be too large/expensive to make it a viable proposition.

DIY is more affordable

The power supply for your Ares looks as though it might benefit from an upgraded PC.

There are several good PC’s out there - Signal Cable Silver Resolution springs to mind, good but affordable.

I would recommend looking at the IC’s between the components and speaker cables

I highly recommend KLE Innovations product mainly because they work extremely well and compared to the competition they start off more reasonably priced

Regards - Steve
In 10 audio's review of the Ares, he notes some minor improvements with use of a PS Audio AC-10 cord, over a DIY cord. He doesn't comment on the stock cord, unfortunately.

I currently use an AC-10 on my Ares (coincidence; I had it before I read the 10-audio review), though I haven't performed direct comparisons yet. I will do so when I get a few nicer cords to play with soon. Having owned a few Ares over the years, I can say that you're going to get a lot more mileage out of the following upgrades, vs. a cord upgrade:

  • Blue Cinemag SUT if you're using an MC cart. The Bob's Devices Sky is slightly better than the 1131, which is similar to a 1254. The difference of any of these, over the stock red 3440, is significant. If you do go for an outboard SUT, the interconnect between it and the Ares is crucial (and keep it 0.5m long).
  • Roll NOS tubes. Telefunkens are a very good 12AX7. Mazda silver plates are even better. You can use 12BH7 in the 12AU7 slots (cleared with Rogue).
  • Get the Magnum upgrades. If you have an outboard SUT or run MM cart you won't need the 1254, but you'll still get audible benefits from just the resistor, PSU, and cap upgrades. 
@mulveling   Thanks for all the suggestions. I've done the Magnum upgrade. 

What is the benefit of the (additional?) SUT? According to Rogue's website, the Magnum upgrade includes "Cinemag blue label step up transformers." Is this all in search of additional gain? My cart is a Rega Apheta II and I get plenty of volume out of it with the Ares set to its specs.

@williewonka : I'm using some DIY power cords at the moment. They're made w/DH Labs "Power Plus Reference" 12 AWG cable and Marinco plugs. All the runs are 2' or less. I had to pull one of them out to do some other work and got to wondering if wrangling all these firehose-size cords is worth the trouble for a device that takes everything to DC anyway. The power supplies are 2 Keces, one 24vAC unit whose manufacturer I can't remember, and the Rogue Ares' OEM. They're all pretty solidly built with heavy metal cases.