I have an MA-505LS, but I've mostly used it with MM cartridges to listen to classical. It should match well with a broad range of MC cartridges, though not necessarily with the heaviest & lowest compliance. I tried an SPU, but couldn't balance it without an extra weight. I'd expect the MA-505XS to be similar.
Advice on best match MC Cartidges for these tonearms
Hi all,
I am re starting my vinyl life, cleaning all 700 odd albums and singles... big job!
I am asking for advice from all those with experience in matching cartridges and tonearms. I have an Ayre K3x pre-amp/phono setup.
I have the following tonearms on appropriate turntables and tonearms have matching original head shells.
Micro Seiki MA-505LS
Micro Seiki MA-505XS
Micro Seiki MAX-327
Kuzma Stogi Ref (currently with a CAR-30 boron)
I listen to a wide range of music, mostly rock, blues, electronic, alternative, classical, pop, 60's 70's 80's era, but limited jazz. I was considering the Ortofon Quintet Bronze, the looked at the Cadenza Bronze for its apparent technical superiority over the lower product lines. I like a warm mellow sound, but with high definition of the instruments. I have not heard the latest lines of cartridges available, but I do know of the much older Ortofon cartridges. I would want at least 2 cartridges that I could swap out with the arms. Any opinions would be really helpful. Cheers A.
- ...
- 10 posts total
There have been many others interested, though, and the range of cartridges seems to go from MM cartridges similar to mine to Denons and Koetsus: https://forum.audiogon.com/discussions/micro-seiki-ma-505-arm-how-good-is-it https://forum.audiogon.com/discussions/dynavector-10-x-5-or-other-mc-in-same-price-range/post?highlight=505%2B103&postid=313848#313848 https://forum.audiogon.com/discussions/quot-oldskool-quot-tonearms/post?highlight=505%2B103&postid=314042#314042 Other than the SPUs, for which you'll need an extra counterweight, you should be fine with almost anything. Given that, you would probably get more responses if you asked the same question without referencing the tonearms, though I'm sure someone would then insist on knowing your tonearm... |
The problem you have is that adjusting the Ayre phono stage for gain ( MM or MC ) and load ( for MC's ) requires removing the lid and adjusting the phono inside the unit. Therefore ideally if using more than one turntable you would be best to pick some cartridges that use the same gain and load. For example you could go with all MM's - Soundsmith moving iron/Gradomoving iron or Ortofon Black are all solid performers. Or you could go with all MC's - most MC's fall into 3-4ohm ( e.g. Koetsu ) or 40ohm internal impedance ( e.g. Benz/Denon/some Dynavector ). Lyra's such as the Delos are less load dependent. My suggestion is decide on MC or MM, then check reviews for your price range - then think about load requirements compared to the CAR. Pick a couple of cartridges with similar load & gain requirements. |
@sampsa55 @dover Thanks for the suggestions. I have been leaning toward the Ortofon Cadenza Bronze, in that it has some good technology used by higher cartridges from the same manufacturer, and is from what I have researched so far, not as "brash" or "clean cut" as the Blacks. I am still researching but numbers are just numbers. People's experiences with different carts add to the whole decision. Lest not forget, there are some seriously expensive carts out there, and even the Bronze is reaching out over the cliff for me. I guess I need to look in the longer term also, the longevity and quality of the product and see if the sums add up. I have heard that some enthusiasts have a drawer full of them to select from depending on the mood. Cool. |
- 10 posts total