SPEAKERS, SPEAKERS AND MORE SPEAKERS.. BUT NEED BASS.?


Greetings audiophile fans,
I am in a challenging dilemma with SPEAKER selection and need a advice.. Budget 4K and less!!
Currently my setup consists ps audio pair mono amps, Jew Rowland pre and Oracle Delphi turntable..
I am mostly listening records (Jazz, folk....) I honestly prefer not to use sub due to space but prefer ful size tower SPEAKERS with enough bass to satisfy my need.. “IT’S ALL ABOUT THAT BASS” 
Soooo what have you heard and recommend for me??
Thanks and happy listening....
Cheers 

128x128shinemaster

@rauliruegas said, "I just can’t imagine any situation in a passive design speakers where subs can’t help to lower speakers IMD that comes with additional benefits as lowering the speakers THD and gives the amps to works way better when are liberated from the low bass range..."

This was in response to me saying "I think that what works best depends on the specific situation."

I’m NOT saying that lowering intermodulation distortion and liberating amp and speaker from the bottom two octaves isn’t beneficial. IT IS!

But in some situations, the circuitry necessary to high-pass-filter the main speakers causes more degradation than it’s worth. For instance if the mains and amp have 10 dB of headroom beyond whatever peaks they’re likely to see then the benefits of a protective high-pass filter may be negligible, and if the speakers are particularly revealing any resulting degradation in the signal path may be audible and objectionable. So imo, "it depends".

Also in many situations budget is a factor. Maybe a really nice high-end signal processor would make a great and super-transparent highpass filter, but is that always going to be the smartest place to spend the next however many hundreds, or thousands, of dollars? Once again, imo "it depends".

Finally there is this possible consideration: An intelligently distributed multi-sub system can significantly reduce room-interaction peaks and dips in the modal zone, and an unusually capable pair of main speakers may have enough useful low-end to contribute to this modal smoothing.

In my experience a fair number of people who are using a protective highpass filter, be it digital or analog, end up pursuing whatever offers the next level of transparency. This may mean hot-rodding the parts inside their device, or it may mean replacing it altogether with the latest-and-greatest. Anyway this tells me that protective highpass filters do have audible downsides.

By building "satellite" speakers that arguably don’t NEED a protective highpass filter under most conditions, I’m giving people the OPTION of not using one. Budget is an issue for most of my customers, so maybe they can defer the expense of that high-end processor for a while, if that’s what they want to end up with.

Duke

Dear @audiokinesis : """  This may mean hot-rodding the parts inside their device. ""

This is what I'm doing through a teflon cap inside my 20.6 monobloks. As a fact I received several improvements because I only change/replace the ML input cap for a way better and lower value/uf teflon/Cu cap along a resistor replace for a top TX2575 Z-foil one that gives me the high pass frequency I need it: around 80hz. I don't have to add any passive device only replace the ones I need to.

In my case was a : " win to win ".

R.

@rauliruegas wrote:  "In my case was a : " win to win ".

That's GREAT!

Using a very-high-quality cap in series with the amp's input as a high-pass filter is probably the most transparent highpass filter format.

The theoretically possible downside is, in the octave above the calculated -3 dB point the output is diminished by an average of about 2 dB, and by almost 1 dB average in the octave above that.  Also the best blend in the crossover region with the steeply-filtered subs might be where the mains are minus more than 3 dB, which increases the region where you are losing energy due to the broad nature of that first-order highpass.  THIS IS NOT NECESSARILY BAD!  It might be an improvement, and it might not; room effects will play a major role in this region so it's impossible to predict accurately. 

Duke


Dear @audiokinesis : In audio always exist trade-offs, nothing is by " free ". The main subject in audio is how good we choosed those trade-offs.

That's what a speaker designer abilities makes the differences. Crossover speakers drivers frequency are determined by the drivers it self, the crossover choosed slopes and what the designer want it: his choosed trade-offs. Unfortunatelly nothing is perfect.

R.

 @rauliruegas , I agree with you 100%!  In audio always exist trade-offs!

Duke